Metabo TKHS 315 M Operating Instructions Manual Download Page 17

ENGLISH

37

10.4 Storing the saw 

A

Danger! 

Store saw so that 

– it cannot be started by unauthori-

sed persons and 

– nobody can get injured. 

A

Caution! 

Do not store saw unprotected out-
doors or in a damp environment. 

10.5 Maintenance 

Before switching ON 

Visual check if distance saw blade – ri-
ving knife is 3...8 mm. 

Visual check of power cable and power 
cable plug for damage; if necessary 
have damaged parts replaced by a 
qualified electrician. 

After switching OFF 

Check to see if the saw blade post-runs 
for more than 10 seconds; if so, have 
the electronic motorbrake replaced by a 
qualified electrician.

Monthly (if used daily) 

Remove saw dust and chips with vacu-
um or brush; apply light coat of oil to 
guide elements: 

– threaded rod of height adjustment; 

– swivel segments. 

After every 300 hours of operation 

Check all screwed connections and re-
tighten if necessary. 

A

Danger!

Have your power tool serviced by a 
qualified repair person using only iden-
tical replacement parts. This will ensure 
that the safety of the power tool is 
maintained.

Contact your local Metabo representati-
ve if you have Metabo power tools re-

quiring repairs. See www.metabo.com 
for addresses.

You can download a list of spare parts 
from www.metabo.com.

Lower saw blade fully. 

Dismount add-on parts (fence, sli-
ding carriage, table extension). 

If possible, use the original card-
board box for shipping. 

For special tasks the following accesso-
ries are available at your specialised 
dealer – see back cover for illustrations: 

A

Sliding Carriage 
For convenient guiding of long 
stock. 

B

Extension table, right
size 1000 mm x 600 mm,
with folding legs 

C

Suction Adapter 
To connect a shop vacuum to the 
dust collection attachment. 

D

Care and Maintenance Spray 
For removing resin residue and pre-
serving metal surfaces. 

E

Saw blade CV 315 x 1.8 x 30 
56 multiple combination teeth 
For solid wood and particle board. 

F

Saw blade CV 315 x 1.8 x 30 
80 neutral multiple teeth 
For especially smooth cuts in solid 
wood and particle board. 

G

Saw blade TCT 315 x 2.8 x 30 
48 universal alternate bevel teeth 
For all woods and wood-derived 
materials. 

H

Saw blade TCT 315 x 2.8/1.8 x 30 
20 square teeth with combination 
pinholes; 
For rip and cross cuts in solid wood. 

I

Saw blade TCT 315 x 3.0/2.0 x 30 
24 alternate bevel teeth 
General purpose blade for rip and 
cross cuts, also in particle board.

J

Saw blade HW 315 x 2.8 x 30 
48 alternate top bevel teeth 
for solid and laminated wood, partic-
le board, MDF, composite materials

K

Saw blade HW 315 x 2.8 x 30 
84 alternate top bevel teeth 

for solid and laminated wood, partic-
le board, MDF, composite materials

L

Roller Stand RS 420 

The machine's packing can be 100% 
recycled. 

End-of-life power tools and accessories 
contain large amounts of valuable raw 
materials and plastics which must be 
recycled. 

This manual was printed on chlorine-
free bleached paper.

A

Danger! 

Before carrying out any fault servi-
cing, always do the following: 

1. Switch machine OFF. 

2. Unplug mains cable. 

3. Wait for saw blade to come to 

standstill. 

Check to see that all safety devices 
are operational after each fault ser-
vice. 

Motor does not run 

Undervoltage relay tripped by power 
failure: 

– switch on again. 

No mains voltage 

– check cable, plug, outlet and mains 

fuse. 

Motor overheated, e.g. by a blunt saw 
blade or chip build-up in the chip case: 

– remove cause for overheating, wait 

for a few minutes, then start saw 
again. 

Motor supply voltage too low: 

– use a shorter extension cable or ex-

tension cable with larger lead cross 
section (

1.5 mm

2

). 

– have power supply checked by a 

qualified electrician. 

11. Repairs

12. Transport 

13. Available Accessories 

14. Environmental Conside-

rations

15. Troubleshooting

Summary of Contents for TKHS 315 M





















Reviews: