manualshive.com logo in svg

MESTA UPS1000-83, Owner'S Manual, Page: 5 / 26

Share
Download
MESTA UPS1000-83 Owner'S Manual Download Page 5

 

1

 

 

1. INTRODUCTION 

Thank you for buying the Mesta Electronics UPS!  You are now an owner of a TRULY 
UNINTERRUPTIBLE POWER SUPPLY.  No other system on the market can match your UPS. 

SAVE THESE INSTRUCTIONS

—This manual contains important instructions that should be followed 

during installation and maintenance of the UPS and its batteries.  Please read this manual thoroughly 
before installation and operation of your new unit. 

WARNING—

Your UPS contains up to eight 12 volt batteries wired in series providing a total nominal 

DC voltage of 96 volts.  This voltage is used to power the UPS when the AC utility is not available.  
Because of the presence of this high voltage energy source, even when the power cord is not plugged 
in, certain precautions must be taken to avoid possible injury should you need to enter your unit.  
Before attempting to enter your unit, read the sections of this manual on "Internal Maintenance" and 
"Battery Information" for important safety precautions. 

Summary of Contents for UPS1000-83



























Reviews:

No comments