manualshive.com logo in svg

MESTA UPS1000-83, Owner'S Manual, Page: 22 / 26

Share
Download
MESTA UPS1000-83 Owner'S Manual Download Page 22

 

18

 

 

×

×

MESTA UPS SPECIFICATIONS 500VA TO 1250VA

Ø

Ø

 

INPUT 

Voltage 

•

 120VAC - 15% + 10% 

Frequency 

•

 60Hz 

±

5Hz (Input frequency 

range is programmable via RS232 port) 

OUTPUT 

Voltage (AC line) 

•

 120VAC 

±

 6% 

Voltage (on inverter) 

•

 120VAC 

±

1% 

Crest Factor Capability 

•

 3.0-*4.0 

Output Power Factor Limitations 

•

 None 

Frequency (AC line) 

•

 follows input 

Frequency (on inverter) 

•

 60Hz 

±

.01Hz 

Frequency Slew Rate 

•

 1–255Hz/sec 

(programmable via RS232 port) 

Total Harmonic Distortion < 1% 
Efficiency 

•

 >92% overall at full load 

Overload Rating  

•

 150% for 1 min. 

 

•

 300% for 1 second 

OVERLOAD PROTECTION 

Output electronically current limited to 300% 

full load rating 

*400% full load rating 

Fuses provide backup protection to 

electronic current limit 

Over temperature protection

 

BATTERY 

Sealed maintenance-free 5 year expected 
life 

INDICATORS AND CONTROLS 

LEDs 

•

 Indicate UPS On, On Line, On Battery, 

Battery Status, and Overload status 
Audible alarm 

•

 indicates loss of AC line, low 

battery or overload 

Reset Switch 

•

 silences alarm, resets 

overloads and is used to initiate UPS in-
service battery test 

Power ON/OFF switches 
RS232 Interface for remote communi-

cations of status and diagnostics 

PHYSICAL 

Operating Temp 

•

 0

°

 C to 40

°

 C ambient 

without derating 

Storage Temp 

•

 -20

°

 C to 40

°

 C 

Thermal 

•

 cooling fan as required 

Audible Noise 

•

 35 dBA 

Line Cord 

•

 6' detachable black 3 wire 

ground with NEMA 5-15P plug 

Output Receptacles 

•

 4 NEMA 5-15R 

RS232 Port 

•

 Interface for remote 

communications

 

OPTIONS 

-B: Automatic bypass to AC line in event of internal UPS problem. 
-H: Hospital grade plugs/receptacles 
-I: Complete line-to-load transformer isolation (increases dimensions / slightly decreases 
efficiency) 
Dry contact relays for external UPS status indication. 
50 Hz Models 
208 or 240 V models in all ranges 

NOTE:  For any of the above options, consult factory.

 

 

Backup Time 

Dimensions 

Models 

Nominal 

BatteryVoltage 

P.F. = .7 

P.F. = 1.0 

H 

L 

W 

UPS500-43 

48V 

23.0 min 

15.0 min 

10.25 

16 

8 

UPS750-43 

48V 

13.5 min 

8.0 min 

10.25 

16 

8 

UPS750-83 

96V 

30.0 min 

20.0 min 

10.25 

21 

8 

UPS1000-83 

96V 

23.0 min 

15.0 min 

10.25 

21 

8 

UPS1250-84 

96V 

17.0 min 

10.0 min 

10.25 

21 

8 

* These enhanced ratings apply only to the UPS1250-84 model 

 

Summary of Contents for UPS1000-83



























Reviews:

No comments