Messersi TC50 Use And Maintenance Manual Download Page 31

Page: 31 / 37

5.6 EXPLOSION ENGINE

For operation, refueling, start-up and shutdown, controls and cleaning, and for
maintenance, follow the indications given in the User’s Manual that the Manufacturer has
supplied with the machine.

5.7 MAINTENANCE SUMMARY TABLE

OPERATION

TO BE

PERFORMED

COMPONENT INVOLVED

HOURS FOR FIRST

REPLACEMENT

100

200

REPLACEMENT

Oil filter cartridge

Hydraulic oil

OPERATION

TO BE

PERFORMED

COMPONENT INVOLVED

FREQUENCY OF SUBSEQUENT

REPLACEMENTS (in hours)

100 250 500 1000

CLEANING

Tracks

Dump body and bucket

Pump body guard space

Hydraulic oil tank

CONTROLS AND
POSSIBLE
REPAIR

Track tightness

Hydraulic oil

REPLACEMENT

Oil filter cartridge

●

Hydraulic oil

GREASING

Grease Points

WARNING!

For the controls to be performed on the endothermic motor, see the User's Manual the
Manufacturer has supplied with the machine.

REFUEL ENGINE

WITH LEAD-FREE

GASOLINE

Summary of Contents for TC50






































Search results

Summary of Contents for TC50

Reviews:

Related manuals for TC50

Brands by name

Popular brands

Messersi TC50, Use And Maintenance Manual

Search results

Summary of Contents for TC50

Reviews:

Related manuals for TC50

Brands by name

Popular brands