background image

13

RADIO

The radio jumper is required to program remote controls. 

For programming procedure please refer to page 12, section “radio”

FREE: 

No programming of remote controls possible

PLUGGED:

Programming of remote controls possible

Important: Keep jumper “RADIO” disconnected

(removed) if not in use!

STOP/8,2 KOhm

Defines whether the terminal STOP/8,2KOhm is used for an

emergency stop or a safety edge. With an emergency stop any

movement of the gate will be stopped. When used for a safety edge

the gate reverses for 1 second.

FREE: 

Factory setting is 8,2KOhm. Safety edge or 

8.2kOhm resistor is required.

PLUGGED: 

Emergency stop required. In this case the 

resistor must be removed  and replaced by the 

switch or a switch circuit.

OPEN/PED

Defines if a key switch opens the gate completely or partially.

FREE: 

opens partially (ca. 100 -150 cm)

PLUGGED: 

opens completely

Note: If the jumper OPEN/PED is plugged and timer to close is

activated as well, the functionality of the terminals “key symbol” and

“COM” changes. See section “Loop Detector” above.

PHO 2 MODE

Defines whether the second photocell is active in closing or in closing

& opening.

FREE:

active in closing

PLUGGED:

active in opening

OBSTACLE

Factory-equipped with fixed wire jumper. Cutting through increases the

operating power at the control. 

CAUTION: If the jumper is severed, the gate system should be

secured with additional safety devices (contact strip, etc.).

Werkseitig mit fester Drahtbrücke ausgestattet. Durchtrennen erhöht

die Arbeitskraft an der Steuerung.

JUMPER SETTINGS

Summary of Contents for XLR8 MGS524





















Reviews: