background image

11

BEEP

AUDIBLE BEEP (OPTIONAL)

AUDIBLE
BEEP

Flash x 2

BEEP

DN

DN

UP

UP

P

P

S

S

1

1

2

2

3

3

The SilentDrive Elite (MR855MYQ) has been
factory set for an audible “BEEP”.

The Audible beep can be turned OFF by using the
following method.

• Start with the door fully CLOSED.
• Press and Hold both “S” and “DN” buttons

for 3 seconds.

• The Courtesy light will flash “TWICE”.

Release the buttons.

To turn the audible beep back ON, simply repeat the
above process.

20

Flash

x2

Door

Fully

Cl

osed

BEEP

UP

UP P

P

S

S

2

2

3

3

BEEP

UP

UP P

P

S

S

2

2

3

3

This is an adjustable, second stop position, that can be pre-

set, partially open for ventilation, pedestrian or pet access,

programmed to the Transmitter.

To activate the ventilation mode:

1.Start with the door fully

CLOSED

(figure 1). Drive the

opener UP and stop at the position required for you wish to

set the door at.

2.Enter ventilation activation mode by pressing the

P

and

UP

buttons together for 3 seconds (figure 2). Release when the

courtesy light flashes once.

3.Press the transmitter button that you have allocated for this

feature (figure 3). Do not use the button already allocated

for normal operation. The courtesy light will flash when the

code is accepted.

The transmitter will now operate to and from the “programmed”

and the “fully closed position”. Outside this range the

transmitter will operate as normal.

To deactivate the partial opening feature:

1.Start with the door fully

CLOSED.

2.Enter ventilation mode by pressing the

P

and

UP

buttons

together for 3 seconds (figure 2). The courtesy light will

flash twice, indicating that deactivation has occurred.

VENTILATION MODE - PARTIAL OPENING FEATURE

21

Summary of Contents for SilentDrive Elite





















Reviews: