background image

96

a

b

c

d

Make sure your rechargeable battery is in 

sound condition 

(a)

. Do not open, disassem-

ble or crush the battery. Risk of explosion!

Make sure your rechargeable battery is not 

exposed to mechanical impacts.

Keep your battery away from fire and heat. 

Risk of explosion!

Batteries must not be short-circuited. There-

fore store them in a safe storage area and 

make sure the battery is not short-circuited 

accidentally (e.g. with another battery). In addition, 

the rechargeable battery must not be stored inappro-

priately, e.g. in a box or in a drawer where they can be 

short-circuited by other conductive materials or where 

they can short-circuit each other. Do not deposit any 

objects in the storage area (e.g. clothes).

Make sure to use the battery only for the 

MERIDA pedelec for which it is designed.

When you remove your battery from the 

holder for charging it 

(b)

 with your MERIDA 

pedelec left in the open during the charging 

process, you should protect the connections, e.g. with a 

plastic bag against rain, water, moisture and dirt 

(c)

. If 

the connections of the rechargeable battery are soiled, 

clean them with a dry rag.

Make sure not to discharge your rechargeable 

battery completely (also referred to as depth 

discharge). This occurs often when the bat-

tery has run out completely and the MERIDA pedelec 

was left standing for some days. Depth discharge 

will affect the rechargeable battery of your MERIDA 

pedelec permanently. A deep-discharged battery can 

only be recharged in exceptional cases and with special 

chargers. Contact your MERIDA dealer.

If the rechargeable battery or the charger (or 

parts of it) must be replaced, only use original 

spare parts. Contact your MERIDA dealer, if 

necessary.

Charge the battery at an ambient tempera-

ture of approx. 20 degrees Celsius. Therefore, 

before starting the charging, wait until the 

temperature of the battery has increased or decreased 

after a ride in cold weather or hot weather.

Do not dispose of your rechargeable battery 

in the normal household rubbish 

(d)

! It must 

be disposed of according to battery dispos-

al regulations. Therefore, sellers of new rechargeable 

batteries must provide collection of old batteries and 

appropriate disposal. If you are in doubt or if you have 

any questions, contact your MERIDA dealer.

Remove the rechargeable battery from your 

MERIDA pedelec or MERIDA e-bike, if you 

do not use your MERIDA pedelec for a longer 

period of time and keep it clean and dry.

Summary of Contents for BIG.NINE E-LITE 600


































































































































Reviews: