manualshive.com logo in svg

Mercury Zeus 3000 Series, User Manual

Share
Download
Mercury Zeus 3000 Series User Manual Download Page 116

Section 5 - Maintenance 

Page  108

90-866938081   MAY  2009

7. Use a 6M Allen wrench and remove the oil filter assembly screw.

a

b

28239

a -

Fluid filter assembly

b -

Assembly screw

8. Remove the filter cover assembly.
9. Remove and discard the filter element and the O‑rings.

a

b

c

e

f

g

h

i

28242

d

a -

Assembly screw

b -

Washer

c -

Cover

d -

Filter cover assembly

e -

O‑ring

f -

O‑ring

g -

Filter element

h -

Seal

i -

Oil pipe

10. Coat the new O‑rings with transmission oil.
11. Install the new O‑rings and filter element.

NOTICE

Improper installation of the transmission fluid filter assembly may cause the fluid to foam

or leak out, resulting in decreased efficiency and damage to the transmission. Properly

seat the transmission fluid filter during installation.

12. Install  the  oil  filter  assembly  in  the  transmission  cavity  by  turning  the  assembly

clockwise during installation.

Summary of Contents for Zeus 3000 Series

































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands