Mercury HP700 SCi Manual Download Page 8

Page: 8 / 138

TABLE OF CONTENTS

viii

Troubleshooting

Engine Will Not Crank .............................................................121

Engine Cranks But Will Not Start.............................................121

Engine Hard to Start, Runs Rough, Misses, and/or Backfires. 122

Poor Performance....................................................................122

Engine Coolant Temperature Too Low....................................122

Engine Coolant Temperature Too High................................... 123

Low Engine Oil Pressure.........................................................123

Power Trim Does Not Operate (Motor Doesn't Run)...............124

Battery Will Not Come Up On Charge.....................................124

Power Trim Does Not Operate (Motor Runs But Drive Unit Does

Not Move)................................................................................124

Electrical Analog Trim Gauge Malfunction...............................124

Remote Control Operates Hard, Binds, Has Excessive Free‑Play

or Makes Unusual Sounds.......................................................125

Steering Wheel Turns Hard or Jerky.......................................125

Seawater Pressure Is Below Specification..............................125

Owner Service Assistance

Local Repair Service................................................................126

Service Away from Home........................................................126

Parts and Accessories Inquiries..............................................126

Service Assistance..................................................................126

Mercury Mercruiser Service Offices.........................................127

Ordering Literature

United States and Canada.......................................................129

Outside The United States and Canada..................................129

Maintenance Log

Maintenance Log.....................................................................130

Summary of Contents for HP700 SCi











































































































































Search results

Summary of Contents for HP700 SCi

Reviews:

Mercury HP700 SCi, Manual, Page: 8 / 138

Search results

Summary of Contents for HP700 SCi

Reviews: