manualshive.com logo in svg

Mercury FourStroke 2.5, Service Manual, Page: 55 / 205

Share
Download
Mercury FourStroke 2.5 Service Manual Download Page 55

Carburetor and Fuel Pump  

Page 3A-2

90-8M0065421   NOVEMBER  2012

Carburetor Specifications

Carburetor Specifications 2.5 HP

Venturi

9 mm (0.35 in.)

Throttle bore

16 mm (0.63 in.)

Main jet

#65

Main nozzle I.D.

1.4 mm (0.06 in.)

Slow jet

#38

Idle air jet

#115

Idle speed (neutral)

1400 ± 50 RPM

Idle speed (forward)

1300 ± 50 RPM

Float level (flange to float bottom)

10 mm (0.39 in.)

Pilot (idle mixture) screw

2 ± ½ turn out

Carburetor Specifications 3.5 HP

Venturi

13 mm (0.51 in.)

Throttle bore

19 mm (0.75 in.)

Main jet

#68

Main nozzle I.D.

1.8 mm (0.07 in.)

Slow jet

#38

Idle air jet

#115

Idle speed (neutral)

1400 ± 50 RPM

Idle speed (forward)

1300 ± 50 RPM

Float level (from carburetor flange to bottom of float)

10 mm (0.39 in.)

Pilot (idle mixture) screw

2 ± ½ turn out

Summary of Contents for FourStroke 2.5














































































































































































































Reviews:

No comments