manualshive.com logo in svg

Mercury FourStroke 2.5, Service Manual, Page: 51 / 205

Share
Download
Mercury FourStroke 2.5 Service Manual Download Page 51

Ignition  

Page 2A-10

90-8M0065421   NOVEMBER  2012

Ignition Specification
   Ignition coil gap

0.3 mm (0.012 in.)

4. Tighten the two ignition coil mounting bolts to the specified torque.
5. Install the spark plug lead onto the spark plug and secure with the J‑clamp.
6. Connect the stop switch tan wire connector.

a -

Ignition coil mounting bolts (M6 x 20) (2)

b -

Ignition coil

c -

J‑clamp

d -

Spark plug lead

e -

Tan wire connector

Description

Nm

lb‑in.

lb‑ft

Ignition coil mounting bolts (M6 x 20) (2)

6

53

7.
8. Apply Loctite 242 Threadlocker to the recoil starter assembly mounting bolts.
9. Install the recoil starter and flywheel cover. Tighten the bolts to the specified torque.

a -

Recoil starter

b -

Flywheel cover

c -

J‑clip

d -

Bolt and washer (M6 x 60) (3)

Tube Ref No.

Description

Where Used

Part No.

66

Loctite 242 Threadlocker

Recoil starter assembly mounting bolts

92-809821

Description

Nm

lb‑in.

lb‑ft

Recoil starter assembly mounting bolts (M6 x 60) (3)

6

53

10. Install the fuel tank assembly.

50000

a

b

c

d

e

c

d

d

d

a

b

49999

Summary of Contents for FourStroke 2.5














































































































































































































Reviews:

No comments