Mercury Epiphone Valve Junior Assembly Manual Download Page 11

Page: 11 / 47

Epiphone Valve Jr.

•

Mercury Upgrade Kit

This project and its documentation is the result of technical investigations made by the engineering staff of

Mercury Magnetics

. The disclosure of the information herein may pertain to proprietary rights and

the furnishing of these documents does not constitute an expresed or implied license to use such materials.

1-5/16”

2-1/2”

4“

3“

2-1/4“

1-5/16”

ANGE/WHITE

YELL

ANGE

RED

ANGE

YELL

RED

3-1/2“

3/16” DIA

RED

B+

YELLOW

BLACK

RED

SECONDARY

(OUTPUT)

ORANGE

6.3V with CT
filament
winding

ORANGE/WHITE

PRIMARY

(INPUT)

120V

Low flux/high impedance inductance design
with primary to secondary humbucking
winding configuration.

Mercury Magnetics

9167 Independence Ave. • Chatsworth, CA 91311
(818) 998-7791 • FAX (818) 998-7835

info@

MercuryMagnetics

.com • www.

MercuryMagnetics

.com

100% of our products are designed & handmade in So. California, USA. • Established in 1954

(All dimensions are nominal)

EPJR-P

CLASS

: Axiom®

TYPE

: Power Transformer

PART NO.

: EPJR-P

ORIGINAL EPIPHONE PART NO

: TC00273

MOUNTING

: Horizontal A-Frame

VA RATING

: 30VA

DATE

: 03-30-06

licensed to Mercury Magnetics. Epiphone is a registered trademark of Gibson Guitar Corp. or its subsidiaries. Mercury Magnetics is not affiliated with Gibson Guitar Corp.

Epiphone Valve Jr.

Origin: Stock Valve Jr.
purchased in April 2005
specifically for modification
purposes.

Summary of Contents for Epiphone Valve Junior
















































Search results

Summary of Contents for Epiphone Valve Junior

Reviews:

Brands by name

Popular brands

Mercury Epiphone Valve Junior, Assembly Manual

Search results

Summary of Contents for Epiphone Valve Junior

Reviews:

Brands by name

Popular brands