Mercury Axius System User Manual Download Page 14 | Manualshive

Page: 14 / 60

background image

Section 1 - Getting to Know the Axius System

Page 10

CMD-4082082 / 90-8M0052072

eng

FEBRUARY 2011

2. Remove the M8 screw and washer securing the handle.

41350

Location of handle screw and washer

3. Remove the handle.
4. Remove the three M5 screws securing the side cover.

41347

Location of side cover screws

5. Remove the side cover.
6. For adjustment, temporarily install the handle, washer and screw. Finger‑tighten the screw.
7. To adjust the ERC handle detent tension:

a. Turn the adjustment screw clockwise to increase tension on the control handle and counter‑clockwise to decrease

tension.

b. Adjust to the desired tension.

8. To adjust ERC handle tension:

a. Turn the adjustment screw clockwise to increase tension on the control handle and counter‑clockwise to decrease

tension.

«
...
12
13
14
15
16
...
»

Summary of Contents for Axius System





























































Reviews:

No comments

Related manuals for Axius System

Brand: Walker Bay Pages: 8

Brand: GE Pages: 802

Brand: iET Pages: 17

Brand: NEC Pages: 54

Brand: Panasonic Pages: 30

Pro Vantage 12+ Series

Brand: Ecco Pages: 6

Brand: IBS Scherer Pages: 64

Brand: jcb Pages: 41

Varycolor MICRO 150HTI

Brand: JB-Lighting Pages: 18

Brand: ParaBody Pages: 3

Brand: Valiani Pages: 66

Brand: Quantum Pages: 11

Brand: Quanser Pages: 21

Brand: Quanser Pages: 18

MCX-C15 - MusicCAST Network Audio Player

Brand: Yamaha Pages: 65

Brand: Yamaha Pages: 24

Brand: Össur Pages: 16

Exoform Dorsal Night Splint

Brand: Össur Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands