manualshive.com logo in svg

Mercury 2004 Sable, Owner'S Manual

Share
Download
Mercury 2004 Sable Owner'S Manual Download Page 67

on, contact your dealer for service as soon as possible. For further
information, refer to

Traction control

娂

in the

Driving

chapter.

DATA ERR.

These messages indicate improper operation of the vehicle

network communication between electronic modules.

•

Fuel computer

•

Charging system

•

Coolant system

•

Traction control (if equipped)

•

Door sensor

•

Brake fluid

•

Compass (if equipped)

•

Outside temperature (if equipped)

•

Engine sensor

•

Transmission sensor

•

Fuel cap sensor

•

Seat belt sensor

•

Park brake

•

Oil pressure sensor

Contact your dealer as soon as possible if these messages occur on a
regular basis.

CENTER CONSOLE

Your vehicle may be equipped with a variety of console features. These
include:

•

Utility compartment

•

Bin mat (snap-in)

•

Cupholders (front and rear)

•

Coin holder slots

•

Compact disc changer (if equipped)

•

Tissue holder

•

Rear A/C vent

•

Rear ashtray (see your Ford, Lincoln Mercury dealer to obtain rear
ashtray

2004 Sable

(sab)

Owners Guide (post-2002-fmt)
USA English

(fus)

Driver Controls

66

Summary of Contents for 2004 Sable


























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands