manualshive.com logo in svg

Mercury 2004 Sable, Owner'S Manual

Share
Download
Mercury 2004 Sable Owner'S Manual Download Page 65

This acts as a reminder that these warning conditions still exist within
the vehicle.

Warnings

Status

Driver’s door ajar

Warning cannot be reset (CLOSE
DOOR TO RESET) will be displayed

Passenger door ajar

Left rear door ajar

Right rear door ajar

Park brake engaged

RELEASE PARK BRAKE will be
displayed

Check engine temp

Warning returns after 10 minutes

Transmission overheated

Check transmission

Low fuel level

Check fuel cap

Check charging system

Oil pressure low

Check brake system

Low brake fluid

Warning returns after the ignition key
is turned from OFF to RUN

Liftgate ajar (if equipped)

Check Traction Control (if
equipped)

Data error

DRIVER’S DOOR AJAR.

Displayed when the driver’s door is not

completely closed.

PASSENGER DOOR AJAR.

Displayed when the passenger side door is

not completely closed.

LEFT REAR DOOR AJAR.

Displayed when the left rear door is not

completely closed.

RIGHT REAR DOOR AJAR.

Displayed when the right rear door is not

completely closed.

PARK BRAKE ENGAGED.

Displayed when the park brake is engaged.

If the warning stays on after the park brake is off, contact your dealer as
soon as possible.

CHECK ENGINE TEMPERATURE.

Displayed when the engine

coolant is overheating. Stop the vehicle as soon as safely possible, turn

2004 Sable

(sab)

Owners Guide (post-2002-fmt)
USA English

(fus)

Driver Controls

64

Summary of Contents for 2004 Sable


























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands