MerCruiser QSD 2.0 Manual Download Page 59

Page: 59 / 135

Section 5 - Maintenance

90-8M0057081

eng

MARCH 2011

Page 51

2. Remove the dipstick. Wipe clean and reinstall into the dipstick tube.

QSD 2.0L engine oil service

a -

Engine cover with access panel removed

b -

Engine oil fill cap

c -

Engine oil dipstick

3. Remove the dipstick and observe the oil level. The oil level must be between the marks on the dipstick. If necessary, add oil.

See

Filling

Engine oil level markings

a -

Dipstick

b -

Minimum operating level

c -

Full mark and maximum operating level

4. Install engine oil dipstick

Filling

IMPORTANT: Do not overfill the engine with oil.
1. Remove the oil fill cap.

QSD 2.0L engine oil service

a -

Engine cover with access panel removed

b -

Engine oil fill cap

c -

Engine oil dipstick

27986

14624

27986

Summary of Contents for QSD 2.0








































































































































Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands

MerCruiser QSD 2.0, Manual

Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands