MerCruiser QSD 2.0 Manual Download Page 46

Page: 46 / 135

Section 4 - Specifications

Page 38

90-8M0057081

eng

MARCH 2011

Description

Where Used

Part Number

Shell Myrina

Engine crankcase

Obtain Locally

Mopar
Texaco Ursa Super TD
Wintershall Multi‑Rekord
Veedol Turbostar
Wintershall VIiva 1

These oils are approved by Mercury Marine and Marine Power Europe. For all temperature operation use 15W40 oil.

Engine Specifications

Description

Specifications

QSD 2.0

Engine type

In‑line 4 cylinder diesel

Induction Type

Turbocharged and Aftercooled 16 Valve

Displacement

2.0 liter (122 cu. in.)

Firing order

1‑3‑4‑2

Bore

83 mm (3.700 in.)

Stroke

92 mm (3.622 in.)

Rated engine RPM (see

Conditions Affecting Operation—Propeller

Selection

for additional information).

Refer to CMD's Marine Performance Curves And

Data Sheet (www.Cummins.com)

Idle RPM in neutral (engine at normal operating temperature).

700 RPM

Oil pressure at idle

2.4 bar [240 kPa] (35 PSI)

Oil pressure at 4000 RPM

6.6 bar [660 kPa] (95 PSI)

Thermostats (water)

83° C (181° F)

Thermostats (oil)

95° C (203° F)

Coolant temperature

80–85° C (176–185° F)

Electrical system

12‑volt negative (–) ground

Alternator rating

14V, 110 A

Recommended battery rating

750 CCA, 950 MCA, or 180 Ahm

Fluid Specifications

IMPORTANT: All capacities are approximate fluid measures.

Engine

IMPORTANT: Fluid level indicators are calibrated to provide accurate readings with the engine level and installed according to

manufacturer's instructions. Modifications may effect fluid level readings.
Always use the proper fluid level indicator to determine the exact quantity of oil or fluid required.

Summary of Contents for QSD 2.0








































































































































Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands

MerCruiser QSD 2.0, Manual

Search results

Summary of Contents for QSD 2.0

Reviews:

Related manuals for QSD 2.0

Brands by name

Popular brands