MerCruiser Axius 350 Instruction Manual Download Page 110 | Manualshive

Page: 110 / 149

background image

Section 5 - Maintenance

Page 102

90-8M0053363

eng

NOVEMBER 2010

NOTE: Minor, transverse cracks (across the belt width) may be acceptable. Longitudinal cracks (in the direction of belt

length) that join transverse cracks are not acceptable.

mc75130-1

•

Fraying

•

Glazed surfaces

•

Proper tension ‑ See

Replacing or Adjusting

for proper specifications.

Replacing or Adjusting

IMPORTANT: If a belt is to be reused, it should be installed in the same direction of rotation as before.
1. Loosen the 16 mm (5/8 in.) locking nut on the adjustment stud.
2. Turn the adjustment stud and loosen the belt, if a new serpentine drive belt is required. Remove the old belt and install a new

belt onto the pulleys.

NOTE: Belt tension is measured on the belt at the location that has the longest distance between two pulleys.

3. Attach the Kent Moore belt tension gauge, or equivalent, to the belt.
4. Put a wrench on the adjustment stud 16 mm (5/8 in.) locking nut.
5. Use a 8 mm (5/16 in.) socket and tighten the adjusting stud to adjust the belt tension.
6. Check the gauge for correct belt tension. The gauge has different ranges for new and used belts.

Kent Moore belt tension gauge shown, all similar

a -

Kent Moore belt tension gauge

b -

Serpentine belt

.

Serpentine belt tension using a tension gauge
Used belt

356–378 N (80–85 lbf)

New belt

467–489 N (105–110 lbf)

7. While holding the adjustment stud at the correct belt tension, tighten the 16 mm (5/8 in.) locking nut.

a -

16 mm (5/8 in.) locking nut

b -

8 mm (5/16 in.) adjusting stud

8. Operate the engine for a short period of time and recheck the belt adjustment.

32544

a

COLOR GUIDE

for

PATENT

2.83918

NEWTONE

NEWT

ONE

b

a

b

32545

«
...
108
109
110
111
112
...
»

Summary of Contents for Axius 350






















































































































































Reviews:

No comments

Related manuals for Axius 350

VLT AutomationDrive FC 300 Series

Brand: Danfoss Pages: 56

Brand: Danfoss Pages: 2

Brand: O.S. engine Pages: 32

Brand: Canaline Engines Pages: 39

IE3-K11R 132S 4 Ex e IIC T3

Brand: VEM Pages: 16

Brand: Doosan Pages: 350

Brand: Champion Power Equipment Pages: 20

Brand: Perkins Pages: 27

LOMBARDINI 9 LD 625-2

Brand: Kohler Pages: 92

Brand: M.T.H. Pages: 26

Throttling Governor Kerosene Stationary Engines

Brand: Worthington Pages: 33

RolloTube S-line Sun DuoFern

Brand: RADEMACHER Pages: 2

Brand: Daewoo Pages: 165

Brand: Yanmar Pages: 20

Brand: Yanmar Pages: 50

Brand: Yanmar Pages: 50

Brand: Yanmar Pages: 65

Brand: Yanmar Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands