background image

2.

The top cover is also held in place with one sheet
metal screw. Remove this screw and slide the top
cover towards the back of the toaster. When
replacing the top cover, be sure that it is properly
positioned in the securing tracks.

3.

The bottom cover is secured by two sheet metal
screws. Remove these screws and pull towards
the front of the toaster. 

NOTE PROPER ORIEN-

TATION OF THE OPEN SIDE OF THE AIR
COOLING VENT. 

This opening must always face

towards the front of the unit to assure proper
toaster performance.

B     Main Power On/Off Switch

(Figures 1 & 2)

1.

Remove the bottom cover.

2.

Disconnect the 2 wires at the on/off switch
terminal ends. Note the correct orientation of the
wires.

3.

Remove the rubber on/off switch boot (old style
units) and the black plastic mounting bezel.

4.

The on/off switch can now be removed from the
back of the control panel.

5.

Reverse this procedure to install a new switch.
(Refer to the wiring diagram)

          

2

ST-1 PARTS REPLACEMENT

INSRUCTIONS

WARNING

DISCONNECT TOASTER FROM

POWER SOURCE

BEFORE ATTEMPTING ANY SER-

VICE PROCEDURES.

General Information

The information on the following pages will
describe how to replace the most common
components of the ST-1 toaster. Though the
instructions are easy to follow, the work should be
done by a qualified service technician. All replace-
ment procedures will first require the removal of
one or both toaster side panels, and top or bottom
covers. 

IMPORTANT: When removing or replacing

the bottom toaster cover, it is extremely impor-
tant that it be positioned correctly. The open side
air cooling vent should be facing towards the
front of the unit. This will assure proper air
circulation and toaster performance.

A      Panel Removal

1.  The right and left side panels are each secured
      to the toaster by one sheet metal screw located
      at the back of the unit. Remove this screw and
      slide

out the panel. When replacing either panel, be
sure that the panel is properly positioned in
the securing track.

Summary of Contents for ST-1









Reviews: