manualshive.com logo in svg

Mercedes-Benz OM 471, Introduction Into Service Manual

Share
Download
Mercedes-Benz OM 471 Introduction Into Service Manual Download Page 194

System components

GF18.20>W>4100H

Oil/coolant module, component description

20.7.11

ENGINE  471.9 in MODEL 963

W18.20

>

1032

>

06

Location

1

Oil/coolant module

The oil/coolant module (1) is located on the
left side of the engine.

Task

The oil/coolant module (1) is used to:

•

Filter the engine oil

•

Regulate the engine oil temperature

•

Regulate the coolant temperature

•

Support the coolant pump

W18.20

>

1037

>

82

Body

1

Oil/coolant module

2

Oil thermostat

3

Oil filter

4

Oil filter cover

5

Oil/water heat exchanger

6

Coolant pump

7

Coolant thermostat

i

  

Introduction of engine OM 471 and exhaust aftertreatment 

>

 09/2011 

>

191

– This printout will not be recorded by the update service. Status: 09 / 2011 –

Summary of Contents for OM 471


































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands