Mercedes-Benz OM 471 Introduction Into Service Manual Download Page 131

Page: 131 / 225

System components

GF83.70>W>4039H

Auxiliary heater unit, component description

20.7.11

MODEL 963, 964 with CODE (D6M) Cab hot water auxiliary heater
MODEL 963, 964 with CODE (D6N) Cab and engine hot water auxiliary heater

W83.70

1434

Location

Shown on auxiliary heater, code (D6N) Cab
and engine hot water auxiliary heater
A901

Auxiliary water heater unit

The heater (A901) is bolted on behind the
left entrance on the cab floor.

Task

The auxiliary water heater unit (A901) is
used for

preheating,

continuous heating,

stationary heating and

heat boosting.

W83.70

1457

Auxiliary heater, code (D6M) Cab hot water
auxiliary heater
1

Burner insert

Burner tube

Heat exchanger

A13

Truck auxiliary heater (ITH)
control unit

A901

Auxiliary water heater unit

A901 B1

Auxiliary heater exhaust
temperature sensor

A901 B2

Temperature sensor

A901 B3

Overheating protection

A901 E

Glow plug

A901 M1 Combustion air blower

Exhaust outlet

Fuel inlet

Coolant outlet

Coolant inlet

Combustion air inlet

128

– This printout will not be recorded by the update service. Status: 09 / 2011 –

Summary of Contents for OM 471


































































































































































































































Search results

Summary of Contents for OM 471

Reviews:

Brands by name

Popular brands

Mercedes-Benz OM 471, Introduction Into Service Manual

Search results

Summary of Contents for OM 471

Reviews:

Brands by name

Popular brands