background image

 

SC35 User Guide Ver 4.8 

August 30, 2002 

Page 25 of 25 

8.  Appendix 

8.1  Contact Information 

For Technical Support or Warranty Repair information, please contact 
Memtech at: 
 
7628 Las Positas Road 
Livermore, CA 94550 U.S.A. 
Phone:  (925) 294-8483 
Fax:  (925) 294-5920 
Email:  

[email protected]

 

 

8.2  SCSI specification information 

Information regarding the SCSI-II specification may be obtained from 
the following locations: 
 
Global Engineering 
15 Inverness Way East 
Englewood, Co. 80112-5704 
Phone: (303) 792-2181 or (800) 854-7179 
Fax: (303) 792-2192 
 

8.3  Limited Lifetime Warranty 

Memtech SSD Corporation (Memtech) warrants your SC35 against 
defects in material and workmanship for the life of the drive.  The 
warranty is void in the case of misuse, accident, alteration, improper 
installation, misapplication or the result of unauthorized service or 
repair. 
 
The implied warranties of merchantability and fitness for a particular 
purpose, and all other warranties, expressed or implied, except as set 
forth in this warranty, shall not apply to the products delivered. 
 
In no event shall Memtech be liable for any lost profits, lost savings or 
other incidental or consequential damages arising out of the use of, or 
inability to use, this product. 
 
BEFORE RETURNING PRODUCT, A RETURN MATERIAL 
AUTHORIZATION (RMA) MUST BE OBTAINED FROM MEMTECH. 
 
Product shall be returned to Memtech with shipping prepaid.  If the 
product fails to conform and warranty repair is necessary, Memtech 
will reimburse customer for the transportation charges incurred. 

 

Summary of Contents for SC35 Mastodon


























Reviews: