background image

CAUTION

• It is normal for the heater to smoke during the first few minutes of use.

• Regularly clean your patio heater after every use.

• If you smell gas – turn off the appliance and extinguish all flames. If the odour

continues, immediately contact your gas supplier.

• In the event of an uncontrollable fire, immediately disconnect the gas cylinder moving

it away from fire and contact the fire services. DO NOT PUT YOURSELF AT RISK!

• Ensure aerosols are not used near this unit when in use.

• Ensure all packaging and plastic bags are disposed of safely.

Technical Data
Overall Height:    

 

90" approx.

Overall Weight: 

 

  84lbs

Overall Width:    

 

34" approx.

Heater Heat Input(·Qn):    

42000 Btu/h

Heater Gas Consumption:   

2.0 Lbs per hour

Heater Injector Size:  

 

0.077"

Setting Pressure:  

 

11" per W.C

Regulator Outlet Pressure:  

11" per W.C

Standard:  

 

 

ANSI Z83.26-(2014).CSA 2.37-(2014)

 

 

 

 

Gas Fired Outdoor infrared Patio heaters

Gas Supply Pressure:  

 

Max.250 PSI, MIN.5 PSI

Specifications are subject to change without prior notice.

Universal Innovations China Ltd.

168# Jianghan Road, Zhijiang City, Hubei Province 443200, China.

Shall be used only in a well ventilated space and shall not be used in a building,

garage or any other enclosed area. Maybe installed in shelter no more inclusive

than:

– With walls on all sides but with no overhead cover.

– Within a partial enclosure which includes an overhead cover and no more 

than two side walls. These side walls may be parallel, as in a breezeway, or

at right angles to each other.

– Within a partial enclosure which includes an overhead cover and three side 

walls, as long as 30% or more of the horizontal periphery of the enclosure is

permanently open.

Warranty

Keep these instructions for future reference.The patio heater has been manufactured under the 

highest standards of quality and workmanship.We warrant to the original consumer purchaser that all 

aspects of this product will be free of defects in material and workmanship for 1 year from the date 

of purchase. A replacement for any defective part will be supplied free of charge for installation by 

the consumer. Defects or damage caused by the use of other genuine parts are not covered by this 

warranty. This warranty shall be effective from the date of purchase as shown in the purchaser’s

receipt.

This warranty is valid for the original customer only and excludes product damage due to shipment 

or failure which results from alteration, product abuse or product misuse whether performed by 

a contractor, service company, or consumer. We will not be responsible for labor charges and/or 

damage incurred in installation, repair or replacement, nor for incidental or consequential damage.

Contact: [email protected] Tel: 678 534 2876

24"(0.6M)

24"(0.6M)

5010530

Summary of Contents for 42000 Btu





















Reviews: