background image

ConnectX®-3 Pro Ethernet Single and Dual SFP+ Port Adapter Card User Manual

Rev 1.5

Mellanox Technologies

48

7.2

MCX312C-XCCT Specifications

Table 8 - MCX312C-XCCT Specifications Table

Physical

Size:

 5.77 in. x 2.7 in. (142.24 mm x 68.9 mm)

Connector:

 SFP+ 10Gb/s 

Protocol Support

Ethernet:

 10GBASE-CX4, 10GBASE-R, and 1000BASE-R

Data Rate:

 1/10Gb/s – Ethernet

PCI Express Gen3:

 SERDES @ 8.0GT/s, 8 lanes (2.0 and 1.1 compatible)

Power and 

Environmental

Voltage:

 12V, 3.3V

Typ Power:

 Passive Cables 6.0W 

Max Power:

 Passive Cables 6.73W

Temperature:

 Operational 0°C to 55°C

Non-operational -20°C to 70°C

Humidity:

 90% relative humidity

a

a. For both operational and non-operational states

Air Flow:

 200LFM

b

b. Air flow is measured ~1” from the heat sink between the heat sink and the cooling air inlet.

Regulatory

EMC:

 Refer to the following link: 

www.mellanox.com/related-docs/user_manuals/Regulatory_and_Compli-
ance_Guide.pdf

Safety:

 IEC/EN 60950-1:2006

ETSI EN 300 019-2-2
IEC 60068-2- 64, 29, 32

RoHS:

 RoHS-R6

Cable Support

Please refer to 

www.mellanox.com

 => Products => Cables and Transceivers

Summary of Contents for ConnectX-3 Pro



































































Reviews: