background image

ConnectX®-3 Pro Ethernet Single and Dual SFP+ Port Adapter Card User Manual

Rev 1.5

Mellanox Technologies

54

Table 11 - SFP+ Connector Pinout

Pin 

 Symbol Name 

Description 

1

 VeeT 

Transmitter Ground (Common with Receiver Ground) 

a

a. Circuit ground is internally isolated from chassis ground.

2

 TX_Fault

Transmitter Fault.

b

b. T

FAULT   

 is an open collector/drain output, which should be pulled up with a 4.7k – 10k Ohms resistor 

on the host board if intended for use. Pull up voltage should be between 2.0V to Vcc + 0.3V. A high 
output indicates a transmitter fault caused by either the TX bias current or the TX output power exceed-
ing the preset alarm thresholds. A low output indicates normal operation. In the low state, the output is 
pulled to <0.8V.

3

 TX_Disable 

Transmitter Disable. Laser output disabled on high or open. 

c

c.  Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V

4

 SDA 

2-wire Serial Interface Data Line 

d

d. Should be pulled up with 4.7kΩ – 10kΩ on host board to a voltage between 2.0V and 3.6V. MOD_ABS 

pulls line low to indicate module is plugged in.

5

 SCL

2-wire Serial Interface Clock Line 

d

6

 MOD_ABS 

Module Absent. Grounded within the module 

d

7

 RS0 

No connection required

8

 RX_LOS 

Loss of Signal indication. Logic 0 indicates normal operation. 

e

e. LOS is open collector output. Should be pulled up with 4.7kΩ – 10kΩ on host board to a voltage 

between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.

9

 RS1

No connection required

10 

VeeR

Receiver Ground (Common with Transmitter Ground) 

a

11 

VeeR 

Receiver Ground (Common with Transmitter Ground)

a

12

 RD-

Receiver Inverted DATA out. AC Coupled

13

 RD+ 

Receiver Non-inverted DATA out. AC Coupled

14

 VeeR 

Receiver Ground (Common with Transmitter Ground) 

a

15

 VccR

Receiver Power Supply

16

 VccT

Transmitter Power Supply

17

 VeeT 

Transmitter Ground (Common with Receiver Ground) 

a

18 

TD+ 

Transmitter Non-Inverted DATA in. AC Coupled.

19

 TD- 

Transmitter Inverted DATA in. AC Coupled.

20

 VeeT

Transmitter Ground (Common with Receiver Ground)

a

Summary of Contents for ConnectX-3 Pro



































































Reviews: