background image

Mellanox Technologies Inc.         350 Oakmead Parkway, Sunnyvale, CA 94085            Tel: 408-970-3400           Fax: 408-970-3403          www.mellanox.com 

BX4000 Series Quick Start Guide 

Document Number

 

3054

Rev 1

.5

Quick Start Guide

Overview 

Mellanox BX4000 series is a 1U, top-of-rack gateway that provides I/O consolidation on both InfiniBand 
and Ethernet. The product supports 10/20/40Gb/S InfiniBand to 1/10Gigabit Ethernet and 2/4/8G Fibre 
Channel.  

The BX4000 series, a top of the rack gateway, provides LAN and SAN connection to the InfiniBand and 10 
Gigabit Ethernet based networks.

The uplink and downlink ports are separated into gateway port groups. Specific uplink ports are assigned 
corresponding downlink ports. Each gateway port group is assigned a color to easily associate the uplink 
ports to the corresponding downlink ports of the gateway port group.

Figure 1:   MTB 4010 Gateway Port Groups Distinguished by Color

 The Port Numbering Table shows the uplink and downlink ports by color, alpha-numeric id identifying the 
IB uplink ports. 

A20 and B20 are InfiniBand ports.

 

Table 1 - MTB 4010B Port Numbering

Gateway 

Port Group

 by Color 

BridgeX 

Controller 

Number

 Uplink 

Ports 

Corresponding Downlink 

FC Ports

Corresponding Downlink 

Ethernet Ports

White

1

A20

    A10    A11    A12    A13

    A10    A11    A12

Orange

1

B20

    B10    B11    B12     B13

    B10    B11    B12 

B20

A20

1 GigE

I2C RS232

Sys

Fan

PSU 1

PSU 2

FC
EN
FC
EN

A1
B1

I2C

IOIO

A11

A12

A13

A10

B11

B12

B13

B10

Mellanox 

®

BX4010

Gateway Port Group A – BridgeX controller 1 – White
Gateway Port Group B – BridgeX controller 1 – Orange

Summary of Contents for BX4000 Series
















Reviews: