manualshive.com logo in svg

MeiTrack T366L, User Manual, Page: 20 / 21

Share
Download
MeiTrack T366L User Manual Download Page 20

MEITRACK T366L

 User Guide                                                                                                 

 

Copyright ©  2020 Meitrack Group All rights reserved.                                                                                                - 20 - 

 

 

8.1.3

 

Setting Code Matching of the RF Remote Control

 

After the cover of the remote control receiver is removed, there will be a purple cable, as shown in the following 

figures. 

Remove the cover

 

 

Cable Color

 

Description

 

Yellow

 

Connect to 5 V power supply. 

Black

 

GND

 

Green

 

Remote control output cable

 

Connect to input 1 (grey cable), which needs to be set to the remote control input. 

Purple

 

Cable for code matching

 

 

Perform the following steps to set code matching: 

1.

 

Connect the remote control receiver's yellow cable to 5 V power supply and code matching cable (purple) to 

GND for more than 2 seconds. 

2.

 

Press any key of the remote control, and then press any key of the other remote control. 

Summary of Contents for T366L






















Reviews:

No comments