background image

7 Installation GPS Antenna

7 Installation GPS Antenna

WARNING!

Antenna mounting without effective anti-fall protection

Danger to life due to fall!

- Pay attention to effective working safety when installing antennas!
- Never work without an effective anti-fall equipment!

WARNING!

Working on the antenna system during thunderstorms

Danger to life due to electrical shock!

- Do not carry out any work on the antenna system or the antenna cable

if there is a risk of a lightning strike.

- Do not carry out any work on the antenna system if the safety distance

to free lines and sequential circuits is exceeded.

Selection of the Antenna location

To receive enough satellites, select a location that allows an unobstructed view of the sky, otherwise there
may be problems with the synchronization of the system. There should be no obstacle in the line of sight
between the antenna and the satellites. In addition, the antenna must not be installed under high-voltage lines
or other electrical light or electric circuits.

Installation conditions for optimal operation:

Free view from 8

above the horizon or

Free view towards equator (if free view of 8

not possible) or

Clear view between 55th southern and 55th northern latitude (satellite orbits).

If all of these views are restricted, complications can arise, because four

satellites have to be located to calculate a new position.

LANTIME

Date: 16th February 2021

27

Summary of Contents for LANTIME M300/MRS/AD10-AD10













































Reviews: