Meinberg GPS170SV Manual Download Page 24

Page: 24 / 42

Page 20

6 Technical Specications GPS170

6.1 Oscillator specifications

Oscilla

tor

s a

vailable f

or Meinber

g GPS R

eceiv

s/Time Ser

ver

OCX

, T

, Rubidiu

TCXO

OCXO LQ

OCXO MQ

OCXO HQ

OCXO DHQ

Rubidium

(onl

y a

vailab

for 3U models)

shor

t term stability

(�

= 1 sec)

2·

-9

1·

-9

2·

-10

5·

-12

2·

-12

2·

-11

accurac

y of PPS

(pulse per sec)

250 ns

100 ns

phase noise

1Hz -60dBc/Hz

10Hz -90dBc/Hz

100Hz -120dBc/Hz

1kHz -130dBc/Hz

1Hz -60dBc/Hz

10Hz -90dBc/Hz

100Hz -120dBc/Hz

1kHz -130dBc/Hz

1Hz -75dBc/Hz

10Hz -110dBc/Hz

100Hz -130dBc/Hz

1kHz -140dBc/Hz

1Hz < -85dBc/Hz

10Hz < -115dBc/Hz

100Hz < -130dBc/Hz

1kHz < -140dBc/Hz

1Hz < -80dBc/Hz

10Hz < -110dBc/Hz

100Hz < -125dBc/Hz

1kHz < -135dBc/Hz

1Hz -75dBc/Hz

10Hz -89dBc/Hz

100Hz -128dBc/Hz

1kHz -140dBc/Hz

accurac

free run,

one da

1·

-7

1Hz

(Note1)

2·

-8

0.2Hz

(Note1)

1.5

·10

-9

15mHz

(Note1)

5·

-10

5mHz

(Note1)

1·

-10

1mHz

(Note1)

2·

-11

0.2mHz

(Note1)

accurac

free run,

1 y

ear

1·

-6

10Hz

(Note1)

4·

-7

4Hz

(Note1)

1·

-7

1Hz

(Note1)

5·

-8

0.5Hz

(Note1)

1·

-8

0.1Hz

(Note1)

5·

-10

5mHz

(Note1)

accurac

GPS-sync

onous,

avera

24h

1·

-11

1·

-11

5·

-12

1·

-12

1·

-12

1·

-12

accurac

y of time

free run,

1 da

4.3 ms

865

µs

4.5

µs

1.1

µs

accurac

y of time

free run,

1 y

ear

16 s

6.3 s

1.6 s

788 ms

158 ms

8 ms

temperature

depandant drift

free run

1·

-6

(-20...70

°C)

2·

-7

(0...60

°C)

5·

-8

(-20...70

°C)

1·

-8

(5...70

°C)

2·

-10

(5...70

°C)

6·

-10

(-25...70

°C)

Not

e 1:

The accur

acy in Hertz is based on the s

tandar

d fr

equency of 10 MHz.

For e

xample: Accur

acy of T

O (fr

ee run one da

y) is

±1

·10

-7

·10MHz =

1 HZ

The giv

en v

alues f

or the accur

acy of fr

equency and �

me (not short t

erm accur

acy) ar

e only v

alid f

or a c

ons

tan

t ambien

temper

atur

e! A minimum �me of 24 hour

s of GPS

-s

yncr

onicity is r

equir

ed be

for

e fr

ee run s

tarts.

Date: 4th November 2013

GPS170SV

Summary of Contents for GPS170SV











































Search results

Summary of Contents for GPS170SV

Reviews:

Meinberg GPS170SV, Manual, Page: 24 / 42

Search results

Summary of Contents for GPS170SV

Reviews: