manualshive.com logo in svg

Meinberg GPS170SV, Manual, Page: 16 / 42

Share
Download
Meinberg GPS170SV Manual Download Page 16

Page 12

3 GPS170SV Features

3.7.7 Selection of Generated Time Code

The time code to be generated can be selected by Menu Setup IRIG-settings or the GPS Monitorprogram

GPSMON32 (except Lantime models). DC-Level Shift Codes (PWM-signal) B00x and modulated sine wave

carrier B12x are always generated simultaneously. Both signals are provided at the VG64-Connector, i.e. if code

B132 is selected also code B002 is available. This applies for the codes AFNOR NFS 87-500 and IEEE1344 as well.

The TFOM eld in IEEE1344 code is set dependent on the 'already sync'ed' character ('#') which is sent

in the serial time telegram. This character is set, whenever the preconnected clock was not able to synchronize

after power up reset. The 'time gure of merit' (TFOM) eld is set as follows.

Clock synchronized once after power up:

TFOM = 0000

Clock not synchronized after power up:

TFOM = 1111

For testing purposes the output of TFOM in IEEE1344 mode can be disabled. The segment is set to all zeros

then.

3.7.8 Outputs

The module GPS170 provides modulated (AM) and unmodulated (DCLS) outputs. The format of the timecodes

is illustrated in the diagramms "IRIG-" and "AFNOR standard-format".

AM - Sine Wave Output

The amplitude-modulated carrier is available at the VG-connector pin 14a. The carrier frequency depends on

the code and has a value of 1 kHz (IRIG-B). The signal amplitude is 3 Vpp (MARK) and 1 Vpp (SPACE) into

50 Ohm. The encoding is made by the number of MARK-amplitudes during ten carrier waves. The following

agreements are valid:

a)

binary "0":

2 MARK-amplitudes, 8 SPACE-amplitudes

b)

binary "1":

5 MARK-amplitudes, 5 SPACE-amplitudes

c)

position-identier:

8 MARK-amplitudes, 2 SPACE-amplitudes

DCLS Output

The pulse width DCLS signals shown in the diagramms "IRIG" and "AFNOR standard format" are coexistent to

the modulated output and is available at the VG connector pin 13a with TTL level.

3.7.9 Technical Data

OUTPUTS:

Unbalanced AM-sine wave-signal:

3 VPP (MARK) / 1 VPP (SPACE) into 50 Ohm

DCLS signal: TTL

12

Date: 4th November 2013

GPS170SV

Summary of Contents for GPS170SV











































Reviews:

No comments