Meinberg GPS167PC Operating Instructions Manual Download Page 3

Page: 3 / 28

Table of Contents

Impressum ............................................................................................ 2

Driver Diskette for DOS/Windows ...................................................... 4

General Information ............................................................................. 5

GPS167PC Features ............................................................................. 6

Time Zone and Daylight Saving................................................. 6

Asynchronous Serial Ports .......................................................... 7

Time Capture Inputs ................................................................... 7

Pulse and Frequency Outputs ..................................................... 7

DCF77 Emulation ....................................................................... 8

Connectors and LEDs in the Rear Slot Cover ..................................... 9

Installing the Radio Clock .................................................................... 9

Setting The Port Base Address ................................................... 9

Configuring the 9 pin Connector .............................................. 11

Mounting the Board .................................................................. 11

Mounting the Antenna .............................................................. 11

Powering Up the System .......................................................... 12

Files on the Diskette shipped with the Board .................................... 13

Support for other Operating Systems ................................................. 13

Copying the distributed Software to the Hard Disk ........................... 13

Using PCPSINFO.EXE ...................................................................... 14

The resident driver for DOS/Windows .............................................. 17

Controlling the Resident Driver ............................................... 18

Firmware Updates .............................................................................. 18

Replacing the Lithium Battery ........................................................... 19

CE Label ............................................................................................ 19

Summary of Contents for GPS167PC





























Search results

Summary of Contents for GPS167PC

Reviews:

Related manuals for GPS167PC

Brands by name

Popular brands

Meinberg GPS167PC, Operating Instructions Manual

Search results

Summary of Contents for GPS167PC

Reviews:

Related manuals for GPS167PC

Brands by name

Popular brands