manualshive.com logo in svg

Meinberg FUNKUHREN ANZ14_V3, Operating Instructions Manual

Share
Download
Meinberg FUNKUHREN ANZ14_V3 Operating Instructions Manual Download Page 3

Inhaltsübersicht

Impressum ............................................................................................ 2

General Information about DCF77 ...................................................... 5

Features of the AM Radio Clock DCF77 ANZ14 V3 ......................... 6

LF Receiver ................................................................................ 6

Microprocessor System .............................................................. 6

Buffered Real Time Clock .......................................................... 7

Display ........................................................................................ 7

Serial Interface ............................................................................ 7

Power Supply .............................................................................. 7

Installation ............................................................................................ 8

Supply Voltage ........................................................................... 8

Mounting the Antenna ................................................................ 8

Configuration .............................................................................. 9

Display Mode ..................................................................................... 10

Firmware Updates .............................................................................. 11

Inquiring Software Revision .............................................................. 11

Rear Panel Connectors ....................................................................... 12

Pin Assignment of the D-SUB Connector ................................ 12

CE Label ............................................................................................ 12

Rear View .......................................................................................... 13

Technical Specificatins ...................................................................... 14

Format of the Meinberg Standard Time String ........................ 16

Component Layout Main Board ............................................... 17

Component Layout Display Board ........................................... 19

Summary of Contents for FUNKUHREN ANZ14_V3





















Reviews:

No comments

Brands by name

Popular brands

Load more brands