Page 5
MIN.
150°F/66°C
MIN.
150°F
/66°C
MIN.
180°F
/82°
C
MIN.
180°F
/82°C
W
ASH
T
ANK
W
A
S
H
T
A
N
K
W
AS
H
T
A
NK
W
A
S
H
T
A
N
K
T
E
MPERA
TUR
E
T
E
M
P
E
R
A
T
U
R
E
T
E
M
PE
R
ATUR
E
T
E
M
P
E
R
A
T
U
R
E
F
IN
A
L
R
INSE
F
IN
A
L
R
IN
S
E
F
INAL
R
INS
E
F
IN
A
L
R
IN
S
E
T
E
MPER
A
TURE
T
E
M
P
E
R
A
T
U
R
E
T
EMP
E
RATUR
E
T
E
M
P
E
R
A
T
U
R
E
SELEC
T
NORMAL
CYCLE
SELEC
T
NOR
MAL
CYC
LE
SELEC
T
EXTENDED
CYC
LE
SELEC
T
EXTEN
DED
CYC
LE
SELE
CT
HEA
VY
CYCLE
SELEC
T
HEAV
Y
CYC
LE
P
O
W
ER
O
N
P
O
W
E
R
O
N
P
O
W
E
R
O
N
P
O
W
E
R
O
N
S
T
AR
T
S
T
A
R
T
S
TAR
T
S
T
A
R
T
C
YCLE
C
Y
C
LE
C
Y
CLE
C
Y
C
LE
D
R
AIN
D
R
A
IN
D
RAIN
D
R
A
IN
or
o
r
or
o
r
O
FF
O
FF
O
FF
O
FF
P
O
WER
P
O
W
E
R
P
OWE
R
P
O
W
E
R
3.3 Uncrating, Positioning and Leveling
1. Remove all shipping and packaging material
from the appliance, including supports and
wrappings. Leave the shipping skid in place
at this time to allow for easier movement to
the installation location.
2. Check for shipping damage as described
in Section 2, “Transport and Shipping.” If
damage is present, call Meiko Customer
Service at
1-800-868-3840
, providing full
details on the customer, serial number and
extent of damage present. Meiko will file a
freight claim based on this information.
3. Move the appliance to the installation area
and remove the skid. Use caution to avoid
damaging the appliance or any of its
components.
4. Using a spirit level, check that the appliance
is level in both directions (front-to-back AND
side-to-side). If necessary, level the
appliance by rotating the bottom section of
each foot.
CAUTION
The machine MUST be level for proper
operation.
3.4 Accessing the Utility Connections
Water supply and drain connections are located
at the lower rear of the machine. The electrical
supply enters through a strain relief at the lower
rear, but the terminal blocks are accessed from
the front of the machine.
To remove the lower front panel:
1. Remove AND RETAIN the four (4) screws
on the bottom edge of the lower front panel.
See Figure 3-1.
2. Slide the panel down and away from the
machine to remove it. As you pull the panel
away, disconnect the ribbon cable for the
Mike 2 controller to avoid damage.
3. The terminal blocks for the main electrical
supply and chemical dispensers (if used)
are located on the left side of the machine
as shown in Figure 3-2.
Remove
4 screws on
bottom edge
Figure 3-1
S
ECTION
3 - I
NSTALLATION
As panel is
removed,
disconnect
ribbon cable to
Mike 2 controller
Figure 3-2
Main electrical
supply terminal
block
Chemical
dispenser
terminal block
