KE680
8
3-a. Press and release the transmitter
or F
button 3 times, [3] LED flash, [3] siren/horn chirp to
indicate you are in
features “Channel 3 Timer Programming mode”.
3-b. Press and release the transmitter
or
button 4 times, [4] LED flash, [4] siren/horn chirp to
indicate you are in features “Channel 4 Timer Programming mode”.
4. Press and hold the valet switch, the timer will immediately start.
5. When the desired interval has passed, release the valet switch. 1 long chirp for confirmation.
(Set to any interval between 1 second and 2 minutes)
Note 1:
If your built-in timer controls window/sunroof closure in your car, DO NOT change the timer setting!
This requires installer-only programming. Changing the value will adversely effect operation and
may cause damage.
Note 2:
Momentary output:
The momentary output selection will output a negative signal from the Channel 4
output immediately when the Channel 4 button is pressed and will continue until the button is released.
Latched output
: The latched output selection will output a negative signal as soon as the Channel 3 (4)
button is pressed and will continue until the button is pressed again.
Latched output / reset with ignition:
The latched / reset with ignition output selection operates just like
the latched output but will reset or stop when the ignition is turned on.
FEATURE “
IV
” PRORAMMING:
1. Turn the Ignition switc
h ‘ON/OFF’ 3 TIMES and stay in the OFF position.
2. Push the Valet switch
8
times and hold it on the
8
th
push until four chirps with a long chirp is heard. Then
release the valet switch. You are now in the Feature
‘IV’
programming mode.
3. Press and relea
se the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
T
ransmitte
r
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulses
1
Exit the programming mode. (3 long chirps to confirm this exit.)
2
Override Without Password Pin Code
/
Press & hold
button for 4 seconds to
delete the Password pin code
Override With Password Pin Code
/
Password pin code programming
Exit:
Turn Ignition to the 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit.
Password Pin Code Setup:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 times and stay in OFF position.
2. Push the Valet switch
8
times and hold it on the
8
th
push until
four
chirps with a long chirp is heard.
Then release the valet switch. You are now in the Feature
‘IV’
programming mode.
3. Press and release the transmitter
button once, [2] LED flash, [2] siren/horn chirp to indicate you are
in features “Password Pin Code Programming mode”.
4. Within 15 seconds, begin to enter your chosen first 9ths digit by pressing and releasing the valet switch
from 1
– 9 times.
5. Within 15 seconds of the last entered 10ths digit, turn the Ignition switch to the “ON” position.
6. Within 15 seconds, enter your chosen second 10ths digit by pressing and releasing the valet switch
from 1
– 9 times.
7. Finish by turning the ignition switch to the “OFF” position.
If the new password code were accepted, the unit would report the newly entered code, by flashing the
LED, first indicating the first digit code has been memorized, pause, and then the second digit code. The
unit will report the new code three times with a one-second pause between each code.
Note: If 15 seconds of inactivity expire, or if the ignition switch is turned “ON” for more than 5 seconds
during of the above steps, the unit will go back to the last successfully stored code. [3] long chirps will
confirm password programming exit.
