Medion MD 4295 Manual Download Page 14

MD 4295 Autoradio BDA_GB 06.12.2002 12:27 Uhr Seite 14 

C

M

Y

CM

MY

CY CMY

K

TROUBLESHOOTING

The unit cannot be switched on.

The CD cannot be loaded or
ejected.

No sound

Function buttons do not work.

CD skips.

Radio not functioning.
Automatic station selector not
functioning.

Station memory not functioning.

The ignition is not switched on.

The fuse is defect.

There is already a CD in the unit.

The CD has been inserted
upside-down.

The CD is very dirty or defect.

Temperature in the car is too high.

Condensation.

Volume set to minimum.

The cables are not correctly
connected.

The built-in microcomputer
cannot function due to noise.

The operating panel is not seated
correctly.

The installation angle of the unit
is greater than 30

°

.

The CD is very dirty or defect.

Defective self-burned CDs

The aerial cable is not correctly
connected.
The broadcast signals are too
weak.

The pink cable is not connected
to the permanent plus pole.

Switch on the ignition by turning
the key.

Change the fuse.

Remove the CD from the player,
then insert a new CD.
Always insert the CD with the
writing facing upwards.

Clean the CD or try to play
another one.

Allow to cool until the ambient
temperature is back to normal.

Switch off the unit for a few hours
and then try again.

Turn up the volume to the
desired level.

Check the cable connections.

Press RESET button.

Check that the operating panel
is seated correctly and firmly.

Adjust the installation angle to
less than 30

°

.

Clean the CD or try to play
another one.

Check the CD in another unit

Firmly plug in the aerial cable.

Select the transmitter manually.

Check the cable connections.

Problem

Cause

Solution

GB 15

GB

Summary of Contents for MD 4295
















Reviews: