aluminum foil. It helps for short sessions.*
6.
Children may use mats or other items with caution and under
supervision of adults, preferably on low heat or negative ions
mode only
. Consult with the child’s pediatrician before using the
FIR pads and use common sense. Do not leave children or toddlers
on the mat, or with the belt, wraps or other hot stone pad without
supervision. They can walk, play or jump on the pad with crystals
and damage inner sensors. Children can disconnect cables and put
them into their mouths and get shocked. Take extra care if your
child has access to the room where the belt or hands wrap or any
other electrical device is located.*
7.
If you use medicines applied by skin patches, you should
definitely consult your doctor
. The absorption rate of a
transdermal medication can change. If you use an adhesive, it
may also unglue from your skin due to sweating.*
8. Cats and dogs love amethyst and gemstone pads. They feel some
energies better than humans. We suggest to
have an additional
waterproof cover for the pad to protect it from any liquid
and make sure your pet will not chew or scratch the cable,
controller or pad. We recommend cheaper and safe non-
powered, non-electric amethyst or gemstone mats for pets
.
Consult with a veterinarian prior to use mats, pads, belt or wraps
for heating. Be careful with pets sleeping on the device. It should
always be turned off without supervision.*
9.
You should always drink A LOT before the session, during the
session and after the session
– if you feel dry mouth it means
that there is not enough water in the body. And it should not
be just water, you may need to replenish some electrolytes and
minerals as Ca, K, Mg, Na. Twitching may be a sign of these salts’
serious deficit or imbalance so if you sweat a lot herbal teas, fruit
juices, and mineral water rich in K and Mg or mineral supplements
may be necessary. Proper hydration also promotes all effects
improving detoxification caused by sweating.*
10.
Overusing the product on maximum temperature may result
in excessive stimulation
. Use moderately on high temperature.
Even if your product can heat in a continuous mode, it is strongly
recommended not to use the high heat settings for more than 3 hours
for your safety! Some temporary symptoms of organism detoxification
(“healing crisis”) may occur especially if you start too fast.*
11.
Detoxification high heat program should not be done without a
doctor’s approval and supervision
. Some drugs, chemicals, and
toxins which we take into our bodies with air or food end up getting
stored in our fat tissue. They can affect you as you mobilize them
and sweat them out. Before toxins are excreted and exit through
the sweat pores they are absorbed from your decomposed by FIR
heat fat tissues into the bloodstream. While traveling on their way
to be eliminated, substances can exert the same effects that they
do when you had originally taken them.
If a lot of residue was
accumulated in your fat tissue and their release is too fast, the
buildup of these poisons can make you feel worse. That is what
is called detoxification or a “healing crisis”
. If you are chemically
allergic or extra sensitive, the dangers of infrared function,
regarding the release of toxins, may be serious. If you feel any signs
of “healing crisis”, stop using the product and consult your doctor
as the same symptoms may be also the signs of serious illness.
12. William Rea, MD, one of the most knowledgeable doctors in the
world regarding environmental toxicity and sauna detoxification,
warns: “
Uncontrolled, too-rapid mobilization can have
devastating effects on chemically sensitive patients
.” Of course
it does not mean that chemically sensitive people cannot get rid
of toxins. Just that it should be done very slowly and carefully, and
with a doctor’s supervised detox program.
Slowly and gradually
increasing heat level, session length, and frequency is the
best path forward
and It is important to immediately decrease
intensity, duration and frequency of sessions and contact your
health professional if you feel symptoms of a “healing crisis”.*
13. The most important thing when you start to use the mat is to
avoid acupressure overstimulation and overheating.
If you would
like to sleep on your mat, do it slowly, adapting your body to
the pressure
. You can start with shorter sessions at bedtime with
3-D Pad and extra cushioning layers and move forward gradually.
It is like acupuncture – there’s no need to overstimulate the body
from the outset, it is better to increase the intensity of pressure
slowly and continuously.
14. Very careful approach is appropriate to FIR heat function.
Our
skin sensors can easily detect the high temperature caused by
standard conduction heat, but our ability to feel the effects
of radiant infrared heat is limited
. The FIR warmth is much
more penetrating, so the hot stone pads should be used on much
lower sensible temperature than a standard heating pad, and it
demands extra care, especially for long or all-night use.
Use common sense, self-educate, listen to your body and we hope
you experience as many positive results as we have, now that you
have your own MediCrystal® Mat, Belt, Pad or Wraps.
*MediCrystal® products are not intended to diagnose, cure, treat, mitigate or prevent any disease, illness or medical condition or to substitute for medical treatment of any kind.
Information here is never to be construed as medical advice. These products and statements have not been evaluated by U.S. FDA (please, see Disclaimer in this user guide, page 11).
TIPS: TROUBLESHOOTING
1.
Ensure the electrical wall socket that you’ve plugged the
apparatus into is working correctly
. Plug another device into it
to ensure it has power. If it is not working, consider checking the
electrical panel as a breaker may have popped (or broken) and
needs to be reset. Or try another electrical wall socket that you
have verified is powering other devices. If you are using a surge
protector, ensure it is working properly. Plug another electrical
device into and verify that it is working.
2.
Ensure the controller’s plug is pushed all the way in to the
belt’s receptacle socket so that it is snug tight with no space
at all between the plug and the mat’s (belt’s or pad’s) or hands
wrap’s socket
. A loose connection can cause loss of signal exchange
between the mat with crystals and the controller, and when too many
errors accumulate the controller’s calibration may fail. Controller
will show error messages or the apparatus will not heat up properly.
3.
Make sure that the power button on the controller has been
turned ON
. The controller may show
OFF
on display. It means
that either preset heating time is over or the connection between
controller and belt or hands wrap is lost. Try adding time,
powering the controller ON/OFF, or reconnecting it.
4. Please activate the timer button and choose one of the timer settings
to start heating.
Some models of the controllers do not activate
heating function unless a timer is set
.
5. Frequent reason for the new controller fault and errors is an
incorrect order of controller connection. Please,
first connect
the pad, mat, belt or wraps to the controller, and only after
this plug the controller into an electrical outlet and turn
the controller ON
. When you disconnect, first turn it OFF, then
disconnect the plug from the socket, and only after this unplug the
controller from the apparatus.
If you connect the controller to
the power source first, the safety program may lock it and go
into safe mode
. It may start to beep or will show OF or OP error
on the screen. The same may happen if there is a loss of signal
interchange between the belt or hands wrap and the controller.
To
reset it just reconnect it in the correct order
.
®
www.MediCrystal.com
9
Summary of Contents for Classic Amethyst Queen Mat
Page 1: ......
