MediaScreen SL Mobile LED 130 Instruction Manual Download Page 2

WARNING: To reduce the risk of electric shock, do not remove cover.

No user-serviceable parts inside. Refer servicing to qualifi ed service personnel.

RISK OF ELECTRIC SHOCK 

DO NOT OPEN 

CAUTION 

To reduce the risk of fire or electric shock, do not expose this apparatus

to rain or moisture.

Dangerous high voltages are present inside the enclosure.

Do not open the apparatus. Refer servicing to qualified personnel.

Do not place containers with water above the apparatus (including on

shelves above, etc.).

About safety symbols

Various symbols are used in these operating instructions to ensure safe use, and to 

protect you and others against the risk of injury and against material damage. The 

meaning of each of the symbols is explained below.

This symbol indicates information that, if ignored or applied

incorrectly, creates the risk of death or serious personal injury.

This symbol indicates information that, if ignored or applied

incorrectly, could possibly create the risk of death or serious

personal injury.

This symbol indicates information that, if ignored or applied

incorrectly, creates the risk of personal injury or material

damage.

Summary of Contents for SL Mobile LED 130




















Reviews: