Quick Installation Guide
Thank you for purchasing the Mede8er Multimedia Player. Please check
www.mede8erforum.com and www.mede8er.eu for updated User Guides and User Manuals in
multi languages.
Power up and Standby.
Plug the AC/DC adapter into the mains outlet and plug the DC Jack
into the DC IN at the rear of the MED600X3D.
DO NOT USE ANY AC/DC ADAPTER AND
ONLY USE THE ONE SUPPLIED
otherwise you may cause damage to the unit.
Press the On/ Off button on the Mede8ers front panel and front fascia LED will
turn on Blue. You can put your Mede8er into standby by pressing the On/ Off
button on the remote. When in standby the front facia LED will turn Red.
TV SYS Toggle Procedure
. The Mede8er has three video output options i.e.
Composite Video (yellow RCA connectors, Component Video (Red - Green-
Blue connectors) and HDMI. Connect the Mede8er to your TV by one of these
connection options (HDMI is recommended) and change the input option on
your TV to match the option you selected. If you do not get see the Mede8er
GUI (Graphical User Interface) on your TV, you will need to toggle the Mede8er
TV output until you get a picture. Each output option also offers different screen
resolution settings and these will need to be adjusted to match the type of TV
used. To change the Video Output on the Mede8er just press the TV SYS button on the remote
and it will change the Video Output to the next available output option. If after pressing the TV
SYS button you still do not get a picture then after a short pause press the TV SYS again until
you see the Mede8er GUI on your TV. Keep repeating this procedure until you see a picture on
your TV. Once you see a picture it may not be of the highest resolution that your TV is able to
display so go to the SETUP - SYSTEM – VIDEO SYSTEM and choose the correct setting.
Checking and installing latest firmware
. Your MED600X3D is future
proof, due to the ability of being able to update the software of the player,
which is called Firmware. (This is not installed on the Hard Disk) To use
your MED600X3D with the best and latest functionality, please check if
the latest firmware is installed by browsing to SETUP – SYSTEM –
SYSTEM INFO. Here you will see SOFTWARE: Vx.xx. Check the current
latest Mede8er Firmware on www.mede8erforum.com or
www.mede8er.eu, where you can also download the latest version. Unzip or Unrar the file and
you will find one file named install.img. Copy this file to the root directory of a Flash Drive. Plug
the flash drive into the Mede8er. Disconnect the power jack at the rear of the Mede8er then plug
it back in - Now press the on/off button and hold it pressed for 10 seconds and then release.
After approximately 15 seconds the LED on the Mede8er with flash red-blue and you will get a
progress bar on your TV display (some TV's will not display this) wait until the Mede8er re boots
- 60 sec. Your Mede8er is now updated.
DO NOT REMOVE POWER DURING THIS
PROCEDURE.
(Wireless) Network.
Refer to user manual on how to connect your MED600X3D to a network.
The MED10WFB WiFi Dongle / MED20PCIE is available for wireless streaming. Please check
your local store or the WHERE TO BUY section on www.mede8er.eu.
Warranty & Support.
Mede8er products carry a 60* month from date of purchase limited
warranty. In the event of warranty service or support, please contact one of the Mede8er
Service Centers; www.mede8er.eu/support, [email protected] or call +31(0)10-7142861
during business hours (CET). In order to obtain the extended warranty service of in total 60*
months after purchase, you need to register your product on www.mede8er.eu/register within 1
month after purchase. * On accessories 24 months applies.
Page1
θ
Summary of Contents for MED600X3D
Page 16: ......
