3510PHW : 28-09-2012
18
19
20
17
CERTIFICATE OF CALIBRATION
We hereby certify that this product has been calibrated
and found to be in accordance with the applicable
SPECIFICATIONS and MECO STANDARDS.
Accuracies of the standard equipment used in this
calibration are traceable to the National Standards.
MECO METERS PVT. LTD.
Plot No. EL-60, MIDC Electronic Zone,
TTC Industrial Area, Mahape,
Navi Mumbai - 400710 (INDIA)
Tel : 0091-22-27673311-16, 27673300 (Board)
Fax : 0091-22-27673310, 27673330
E-mail : [email protected]
Web : www.mecoinst.com
SR. NO
: __________________________
CHECKED BY : __________________________
DATE
: __________________________
MODEL NO
: __________________________
®
4.7 Temperature Measurement
1. Set the rotary switch to the “ Temp ” position.
2. Press RANGE button to select desired
0
C or
0
F
temperature units.
3. Insert the Type K thermocouple to the Temp jack.
4. Use temperature probe to touch the object being
measured and read the displayed value.
4.8 AC + DC Micro-Ampere Measurement
1. Set the rotary switch to the “
m
A” position.
2. Insert the test leads into the input jack. (Black to COM
and Red to
m
A).
3. Connect the test in series with the circuit being measured
and read the displayed value.
4.9 To disable Auto Power Off function
The meter will automatically enter sleep mode if no button
is pressed and no function is changed for 30 minutes to
save power consumption.
1. Set the rotary switch to the “ OFF ” position.
2. Press and hold “ HOLD ” key then set the rotary switch to
“ ~A ” Position, the auto power off function will be disabled.
The auto power off mark “ ” will disappear.
Auto power off mode is enabled each time you turn on
the meter and is automatically disabled in the “MX / MN”
mode.
4. BATTERY REPLACEMENT
WARNING
To prevent electrical hazard or shock, turn off clamp meter
and disconnect test leads before removing back cover.
1. As battery power is not sufficient, LCD will display
“
”. Replacement with one new battery type 9V is
required.
2. Set range switch to OFF position.
3. Use a screwdriver to unscrew the screw secured on
back cover. Take out the batteries and replace with one
new battery Type 9V.
4. Place back cover and secure with the screw.
4.4 Resistance & Continuity Measurement
WARNING
Before taking any in circuit resistance measurement,
remove Power from the circuit being tested and
discharge all capacitors.
1. Before taking resistance measurement, make sure the
circuit is not live and discharge any capacitors present
in the circuit.
2. Set the rotary switch to the “
V,
” or “ M
V
” range.
3. Insert the test leads into the input jack. (Black to COM
and Red to
V
).
4. Connect the test leads to the circuit being measured
and read the displayed value.
5. When the reading is below 40
V
, it will be indicated by a
continuous beeping.
4.5 Capacitance Measurement
1. Fully discharge the capacitor being tested, will speed
test response time.
2. Insert the test leads into the input jack. (Black to COM
and Red to
).
3. Set the rotary switch to the “
” position.
4. Connect the red test leads to the positive side and black
test lead to the negative side of the capacitor being tested.
5. Read capacitance value on LCD.
4.6 Diode & Continuity Measurement
1. Set the rotary switch to the “
” range.
2. Insert the test leads into the input jack. (Black to COM
and Red to
).
3. Connect the red test lead to the anode side and black
test lead to the cathode side of the Diode being tested.
4. When the reading is below 40mV, it will be indicated by a
continous beeping.
