manualshive.com logo in svg

Measurement Computing TC-32, User Manual

Share
Download
Measurement Computing TC-32 User Manual Download Page 23

TC-32 User's Guide 

Specifications 

23 

Network factory default settings 

Table 14. Factory default specifications 

Parameter 

Specification 

Factory default IP address 

192.168.0.101 

Factory default subnet mask 

255.255.255.0 

Factory default gateway 

192.168.0.1 

Factory default DHCP setting 

DHCP + link-local enabled 

Network security 

Table 15. Factory default specifications 

Parameter 

Specification 

Security implementation 

TCP sockets are not opened unless application sends the correct PIN code (stored 
in non-volatile memory, may be changed by user, default value 0000) 

Number of concurrent sessions 

1 

Vulnerabilities 

TCP Sequence Number Approximation Vulnerability 

LED displays and the factory reset button 

Table 16. LED and button configurations 

Parameter 

Specification 

POWER

 LED (top) 

Indicates power on. Blinks when blink command is sent. Both the 

POWER

 and 

ACTIVITY

 LEDs blink in firmware upgrade mode. 

ACTIVITY

 LED  

On when there is a valid connection and blinks when a command is sent to the  
TC-32. Both the 

POWER

 and 

ACTIVITY

 LEDs blink in firmware upgrade mode. 

ALARM

 LED 

Indicates that an alarm condition is met. 

OPEN TC

 LED (bottom) 

Indicates that there is an open thermocouple condition. 

Factory reset button 

When held for 3 seconds, the LEDs turn off for a short time, indicating a reset is in 
process. When the LEDs turn back on, reset is complete and the factory-default 
network settings are restored. 

Environment 

Table 17. Environmental specifications 

Parameter 

Specification 

Operating temperature range 

0 °C to 45 °C 

Storage temperature range 

–40 °C to 85 °C 

Humidity 

0 °C to 90% non-condensing 

Mechanical 

Table 18. Mechanical specifications 

Parameter 

Specification 

Dimensions (L × W × H) 

482.6 × 128.6 × 43.18 mm (19 × 6.15 × 1.74 in.) 

Distributed by MicroDAQ.com, Ltd.               www.MicroDAQ.com               (603) 746-5524

Summary of Contents for TC-32




























Reviews:

No comments

Brands by name

Popular brands

Load more brands