manualshive.com logo in svg

Measurement Computing TC-32, User Manual

Share
Download
Measurement Computing TC-32 User Manual Download Page 15

TC-32 User's Guide 

Functional Details 

15 

EXPANSION connector  

Use the 

EXPANSION

 connector to connect the TC-32 to a TC-32-EXP expansion device (sold separately) for 

applications that need additional analog/thermocouple input and digital I/O channels. A 40-pin expansion cable 
is included with the TC-EXP-32.  

Refer to 

www.mccdaq.com

 for TC-32-EXP product details. 

Chassis ground connector 

Provides a connection point (#6-32 screw) for chassis ground. Connect this to an external grounding source. 

If the TC-32 is connected by USB or by a shielded Ethernet cable to grounded equipment, connecting to an 
external grounding source is not needed since the USB/shielded Ethernet connection already grounds the TC-32 
and a connected TC-32-EXP.  

RESET button 

Press and hold this button to restore the TC-32 to its factory default network settings. Refer to 

Restoring factory 

default network settings

 on page 10 

 

 

Distributed by MicroDAQ.com, Ltd.               www.MicroDAQ.com               (603) 746-5524

Summary of Contents for TC-32




























Reviews:

No comments

Brands by name

Popular brands

Load more brands