2
1.4
Main Specification
VOLTAGE ADJ. RANGE
105 ~ 115% rated output power
MODEL
DC VOLTAGE
RATED CURRENT
OUTPUT
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE
Note.4
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
Note.10
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVER TEMPERATURE
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
DIMENSION
OTHERS
NOTE
OVERLOAD
OVER VOLTAGE
AC CURRENT (Typ.)
1500ms, 60ms/230VAC at full load
90 ~ 264VAC 127 ~ 370VDC
Cold start 80A/230VAC
2mA / 240VAC
-30 ~ +70
Baseplate temperature (Refer to “Derating Curve")
℃
20 ~ 90% RH non-condensing
-40 ~ +85
, 10 ~ 95% RH non-condensing
℃
±
℃
℃)
0.03%/
(0 ~ 50
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
183.4K hrs min.
Telcordia SR-332 (Bellcore) ; 56.26K hrs min. MIL-HDBK-217F (25
)
℃
PF
0.95/230VAC at full load
≥
16ms/230VAC at 75% load 10ms/230VAC at full load
RIPPLE & NOISE (max.)
Note.2
VOLTAGE TOLERANCE
Note.3
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance :
line regulation and load regulation.
includes set up tolerance,
4. Derating may be needed under low input voltages. Please check the
for more details.
derating curve
5. Without water or fan cooling to provide adequate heat dissipation, OTP might be triggered if trimming output voltage by PV signal toward upper or bottom
limits of nominal voltage. Under such condition, enhanced cooling on PSU is highly recommended.
6. PV/PC function when users are not operating on PMBus. SVR functions when users are neither operation on PMBus nor using PV/PC.
7. Need additional EMI filter to meet regulations of EMC conducted and radiated emission. Characteristics of EMI filter please refer to the table, Minimum
Insertion Loss.
8.
The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on
a
mm*
mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives.
600
900
For guidance on how to
perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com)
9. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).
℃
℃
10. The efficiency is measured at 75% load.
ENVIRONMENT
PROTECTION
380*141.4*60mm (L*W*H)
Protection type :Shut down O/P voltage,re-power on to recover
Protection type :Shut down O/P voltage, recovers automatically after temperature goes down
20A/230VAC
RATED POWER
(convection)
4.5Kg;4pcs/19Kg/2.51CUFT
47 ~ 63Hz
Protection type : Constant current limiting, shut down O/P voltage 5 sec. after O/P voltage is down low, re-power on to recover
FUNCTION
REMOTE ON/OFF CONTROL
AUXILIARY POWER
DC-OK SIGNAL
Power ON : Short circuit Power OFF : Open circuit
[email protected] tolerance 10%, ripple 150mVp-p
±
The TTL signal out, PSU turn on = -0.5 ~ 0.5V ; PSU turn off = 3.5 ~ 5.5V. Please refer to the Function Manual.
SAFETY STANDARDS
SAFETY &
EMC
(Note.7,8)
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:1.25KVAC
I/P-O/P, I/P-FG,O/P-FG:100M Ohms/500VDC/25
/ 70%RH
℃
UL62368-1,TUV EN62368-1,
approved ; design refers to EN61558-1, EN60335-1
EAC TP TC 004
MTBF
PACKING
Adjustment of constant current level is allowable to 20 ~ 100% of rated current. Please refer to the Function Manual.
OUTPUT VOLTAGE
PROGRAMMABLE(PV)
Note.5,6
OUTPUT CURRENT
PROGRAMMABLE(PC)
Note.6
By built-in potentiometer, SVR
300mVp-p
480mVp-p
±
0.5%
±
0.5%
±
0.5%
±
0.5%
±
1.0%
±
1.0%
95%
96%
30 ~ 36V
60 ~ 72V
PHP-3500-24
PHP-3500-48
3480W
3504W
24V
48V
145A
73A
24~28.8V
48~57.6V
EMC IMMUNITY
EMC EMISSION
Parameter
Parameter
ESD
Radiated
EFT / Burst
Surge
Conducted
Magnetic Field
Voltage Dips and Interruptions
Conducted
Radiated
Harmonic Current
Voltage Flicker
Standard
Standard
EN55032 (CISPR32) / EN55011 (CISPR11)
EN55032 (CISPR32) / EN55011 (CISPR11)
EN61000-3-12
EN61000-3-3
EN61000-4-2
EN61000-4-3
EN61000-4-4
EN61000-6-2
EN61000-4-6
EN61000-4-8
EN61000-4-11
Test Level / Note
Test Level / Note
Level 3, 8KV air ; Level 2, 4KV contact
Level 3
Level 3
2KV/Line-Line 4KV/Line-Earth
Level 3
Level 4
>95% dip 0.5 periods, 30% dip 25 periods,
>95% interruptions 250 periods
Class B
Class A
-----
-----
OVER VOLTAGE CATEGORY
Ⅱ
; According to EN61558; altitude up to 5000 meters.
Adjustment of output voltage is allowable to 50 ~ 120% of nominal output voltage. Please refer to the Function Manual.
