MDS Power IPSi2400X Installation & Operation Manual Download Page 14

14

Specifications

Input

Input Voltage Range

205 -390 VDC

Maximum Input Current

< 20A

Undervoltage Input Threshold < 180 VDC
Overvoltage Input Threshold

> 390 VDC

Reverse Polarity Protection

 Yes

Output

Voltage

110 ± 2 VAC

220 ± 4 VAC

Output Amps (cont)

22.0 A (Cont.) / 28.0 A (Max.)

10.0 A ( Cont.) / 12.0 A (Max.)

Output Frequency

50.00 or 60.00 ± <1 Hz

Duty Cycle

Capable of 2x Maximum Output Power for 10 seconds

Maximum Output Power

1205 series: 1200W
2405 series: 2400W

Output Connection

AC OUT 1:

 2x NEMA 5-20 AC receptacle 739W-X2/20

AC OUT 2:

 3x Phoenix VDFK-4 Terminal Block (Black: Hot, Green: Ground, Grey: Neutral) 

DC IN:

 2x Phoenix VDFK-4 Terminal Block (Red: Positive and Black: Negative)

* Specifications subjects to change without notice.

General

Efficiency

> 80% @ Maximum Output

Temp. Range

-40°C to +55°C @ Maximum Output

Emissions

Designed to meet FCC Part 15 Class A

Shock and Vibration

Designed to meet MIL-STD810H

ROHS3 Compliant

Yes

Connectors

AC OUT 1- Universal AC Receptable S.203013
AC OUT 2- Phoenix VDFK-4 Terminal Block (Black: Hot, Green: Ground and Grey: 
Neutral) 
DC IN - Phoenix VDFK-4 Terminal Block (Red: Positive and Black: Negative)

Length

18.68 in /47.45 cm

Width

11.75 in / 29.85 cm (including mounting flanges)

Height

5.60 in / 14.22cm

Clearance

1.00 in / 2.54 cm (all around)

Material

Marine grade aluminum

Finish

Black powder epoxy/Black anodized

Fastenings

18-8 Stainless steel

Weight

52.5 lb / 24.0 kg (Approximate)

Summary of Contents for IPSi2400X

















Reviews: