manualshive.com logo in svg

McQuay MQIU-174018-HCU216A, Installation And Operation Manual

Share
Download
McQuay MQIU-174018-HCU216A Installation And Operation Manual Download Page 6

● When selecting auto mode, air conditioner will operate automatically according 

   to ex-factory setting. Set temperature can’t be adjusted and will not be displayed

   as well. Press "FAN" button can adjust fan speed. Press "     " button can adjust

   fan blowing angle.

● After selecting cool mode, air conditioner will operate under cool mode. Cool 

   indicator "     "on indoor unit is ON. Press "+" or "-" button to adjust set tempe-

   rature. Press "FAN" button to adjust fan speed. Press "     " button to adjust fan 

   blowing angle.

● When selecting dry mode, the air conditioner operates at low speed under dry 

   mode. Dry indicator "     " on indoor unit is ON. Under dry mode, fan speed can’t

   be adjusted. Press "     " button to adjust fan blowing angle.

● When selecting fan mode, the air conditioner will only blow fan, no cooling and 

   no heating. All indicators are OFF. Press "FAN" button to adjust fan speed. Press

   "     " button to adjust fan blowing angle.

● When selecting heating mode, the air conditioner operates under heat mode. 

   Heat indicator "      " on indoor unit is ON. Press "+" or "-" button to adjust set

   temperature. Press "FAN" button to adjust fan speed. Press "     " button to adjust

   fan blowing angle. (Cooling only unit won’t receive heating mode signal. If setting 

   heat mode with remote controller, press ON/OFF button can’t start up the unit).

Note:

● For preventing cold air, after starting up heating mode, indoor unit will delay 1~5

   minutes to blow air (actual delay time is depend on indoor ambient temperature).

● Set temperature range from remote controller: 16~30

℃

; Fan speed: auto, low 

   speed, medium speed, high speed.

3.3 

Introduction for buttons on remote controller

Note:

● After putting through the power, the air conditioner will give out a sound.

   Operation indictor "     " is ON (red indicator). After that, you can operate the air 

   conditioner by using remote controller.

ON/OFF button

MODE button

1

2

Press this button can turn on or turn off the air conditioner. After turning on the air

conditioner, operation indicator "     "on indoor unit’s display is ON (green indicator.

The colour is different for different models), and indoor unit will give out a sound.

Press this button to select your required operation mode.

AUTO

COOL

FAN

DRY

HEAT

4

Summary of Contents for MQIU-174018-HCU216A









































Reviews:

No comments

Brands by name

Popular brands

Load more brands