mcmurdo Kannad Marine R10 AIS MOB Service Bulletin Download

Page: 3 / 10

Orolia Ltd, Silver Point, Airport Service Rd, Portsmouth, Hants, PO3 5PB, United Kingdom

Tel: +44 (0) 23 9262 3900 Fax: +44 (0) 23 9262 3998 Email:

Page | 3

2. DISASSEMBLY

2.1:

Remove the activation cap. The beacon will activate. Switch off the beacon by
pushing and holding the ‘Off’ button – the beacon should switch off after
approximately 3 seconds.
NOTE: Do not allow beacon to operate for longer than 15 seconds.

2.2:

Remove LED cap by removing 2 off Screws.

2.3:

Remove the battery. The PCB & foil insert do not need to be removed.

Note:

The battery should be disposed of in a sensible and considerate manner, and

in accordance with local regulations. Also the LED cap and gasket are not reusable
and should be disposed of.

Summary of Contents for Kannad Marine R10 AIS MOB











Search results

Summary of Contents for Kannad Marine R10 AIS MOB

Reviews:

Related manuals for Kannad Marine R10 AIS MOB

Brands by name

Popular brands

mcmurdo Kannad Marine R10 AIS MOB, Service Bulletin

Search results

Summary of Contents for Kannad Marine R10 AIS MOB

Reviews:

Related manuals for Kannad Marine R10 AIS MOB

Brands by name

Popular brands