background image

 

9

WARNING    

 

When replacing the high current power output fuses, ensure that the supply capacitors are FULLY 
DISCHARGED before inserting the new ones. 

 

If  the  replaced  fuse  blows  again  then  there  is  a  serious  fault  within  the  unit.  Refer  to  a  service 
engineer or contact your dealer. NEVER INCREASE THE RATING OF THE FUSE. 

 

REMOTE CONTROL OPTION 

 

The MC450, MC650, MC750 are internally wired for remote control, which is easily achieved by 
installing the appropriate interface/drive board during the manufacturing process, without any change to 
the amplifiers’ performance. 

 

Description 

 
The system is designed to replicate via Windows all the controls that are available on the front panel of 
the amplifier (except power-on/off). This means that the volume can be turned up and down, the channels 
can be linked/un-linked and muted/un-muted remotely.  
 

Features 

 

 

Up to 128 amplifiers can be ‘daisy-chained’ together from an RS485 port via an RS232-485  
adaptor. 

 

 

Amplifiers can be grouped together and controlled all at the same time within that group. 

 

 

The front panel controls on the amplifiers can be ‘locked out’ so that they can only be controlled 
from the computer. This allows the system to be set up to the client’s requirements and then made 
secure against manual interference. 

 

 

Two levels of security are available on the management control system through the use of 
passwords, which permit a higher level access for the senior manager through one password and 
more limited access at a lower level to a number of other ‘users’. 

 

 

Full Windows software is available on www.download.at/mc2a 

 

Wiring information 

 

The interconnecting cable required is a twisted pair cable for short runs and a screened, low capacitance 
data  cable  for  long  runs. The  connectors  are  9-way  D-type  and  the  wiring  of  this  connector  on  the  rear 
panel complies with the standard two wire RS485 configuration as follows: 

 

 

 

 

 

 

Signal   

      Pin No. 

 

 

 

 

  

 A (+)   

        2 & 8 

 

 

 

 

  

 B (-)   

        3 & 7 

 

 

 

 

 

 

Screen   

           5 

 

 

All the ‘A’s should be joined together and all the ‘B’s joined together. 

 

 

Pins 2 & 8 and 3 & 7 are joined inside the amplifier to ease the ‘daisy chain’ wiring. 

 

 

The cable screen should be terminated at one place only, i.e. PIN 5 of the computer. 

 
 
 
 
 
 

Summary of Contents for MC450











Reviews: