background image

 

MBS IDNR 8.6.0251/02-2020 (Index_04)

 

 

page 4 of 9 

 

 

Technical data 

 

FASK: Used material 

 
Model 

FASK 100, 150, 200 and 300 

Coil & connection cable Thermoplastic rubber flame retardant according to UL 94 V-0 
Fastener 

acc. PA6 UL 94 V-0 

Colour (Coil) 

orange 

Shielding 

100% coil and 100% electric wire 

 

FASK: Safety 

 
Model 

FASK 100, 150, 200 and 300 

Certifications 

 CE certified (This product satisfies the provisions of the low voltage directive 2014/35/EU 

 

This product satisfies the provisions of RoHS 2.0 directive 2011/65/EU 

 

Protection degree: IP 68 

Insulation voltage 

coil: 3000V 

 

electric wire: 1000V 

Measurement cat. 

1000V CATIII; 600V CATIV 

 

FASK: Technical data 

 

Model 

FASK-100 

FASK-150 

FASK-200 

FASK-300 

Coil length 

395 mm 

525 mm 

665 mm 

965 mm 

Window size 

100 mm 

150 mm 

200 mm 

300 mm 

Reference rated current 

1,000 A 

3,000 A 

6,000 A 

10,000 A 

Weight 

app. 100-160 g 

Output signal 

100 mV/kA @ 50 Hz 

Transformation errors 

< 0.5 % (central position near the fastener @ 25 °C) 

Phase error 

≤ 0.5 ° (30 arc minutes) 

Maximum current measurable 

100 kA 

Coil resistance 

between 100 and 250 Ohm 

Coil diameter (orange cable) 

8 mm 

Connection cable length 

3 m / 5 m 

3 m 

3 m 

3 m 

Temperature coefficient 

400 ppm/K 

Position error 

± 1 % maximum 

Linearity error 

± 0.2 % maximum of the measured value 

Bandwidth 

1 Hz up to 100 kHz (- 3dB) 

Ambient temperature 

-30 up to +80 °C 

Storage temperature 

-40 up to +90 °C 

 

 

Summary of Contents for FASK-100










Reviews: