MBM FC 10 PLUS Page 35 Operation Manual Download

Page: 35 / 40

7.2 Troubleshooting

Troubles

Possible cause

Action

The POWER has been
switched on, but does
not indicate on the
operation panel.

The power cord is not plugged in.

Insert the power plug into the outlet.

The circuit breaker is activated.

Reset the circuit breaker.

Internal trouble of the machine

Contact

your dealer or authorized service

representative.

The

START/STOP

key has been pressed,
but the machine does not
work.

A paper check is required.
A warning will beep and “ ” (no
indication) will appear.

Press the CHECK key for trial feed.

The CHECK key has
been pressed, but the
machine does not work.
Lamps on the operation
panel light or flash,
indicating irregularities.

The back door is not closed
completely.

Close the door securely.

The stacking table is full or a paper jam
is occurring on the stacking table.

Remove delivered or jammed paper.

A paper jam has occurred on station.

Remove jammed paper.

When the stapler-puncher is in use, a
paper jam or a blown fuse has occurred
within the stapler-puncher, or the
stapler-puncher has run out of staples.

Remove the cause of the trouble.

Internal trouble of the machine

Contact

your dealer or authorized service

representative.

The machine has started
operation by pressing
the

START/STOP

key

or the CHECK key, but
no paper is fed.

Sheets are not set properly.

Set sheets securely on a feed table.

Paper jams on the
stacking table occur
frequently, or sheets are
not stacked neatly.

Stacking table paper guides are not set
properly.

Adjust the paper guides.

Paper jams, double feed
or empty feed occur
frequently.

Paper feed rollers are dirty.

Clean the paper feed rollers.

Separators are dirty.

Clean the separators.

Sheets of paper are curled.

Straighten curled papers and set sheets on feed
table.

Feed rollers are worn.

Replace the rollers (Contact your dealer or
authorized service representative.)

Separators are worn.

Replace the separators. (Contact your dealer or
authorized service representative.)

Paper feed tables have been attached or
removed while the power switch is on.

Reset the feed tables after switching off the power.

To reset the breaker, please

push the projected portions

of the breaker shown in the

right figure, marked with

white arrows (2 places)

Summary of Contents for FC 10 PLUS









































Search results

Summary of Contents for FC 10 PLUS

Reviews:

Related manuals for FC 10 PLUS

Brands by name

Popular brands

MBM FC 10 PLUS, Operation Manual

Search results

Summary of Contents for FC 10 PLUS

Reviews:

Related manuals for FC 10 PLUS

Brands by name

Popular brands