MBM AeroFold 1500S Operation Manual Download

Page: 2 / 52

Introduction

Thank you for purchasing UCHIDA

Model “AeroFold” Air Suction Paper Folder.

You should receive

many years of reliable service from this machine. Compact and easy to use,

“AeroFold”

is sure to

streamline your paper folding tasks, saving you valuable time. Please read the Operation Manual
thoroughly before using this machine.

Contents

Safety Instructions .................................................................................... 4

(1) Specifications ........................................................................................ 7

(2) Accessories ............................................................................................ 8

(3) Part Names ......................................................................................... 10

(4) Designation and Functions of Operations Panel ............................. 11

(5) Setup ................................................................................................... 12

(A) Setting of the Paper Ejection Table .......................................................................................... 12

(B) Setting of Table 1 ..................................................................................................................... 13

(C) Setting of Table 2 ..................................................................................................................... 14

(D) Setting of the Auxiliary Paper Feed Table ............................................................................... 16

(E) Connecting Power Cabler ......................................................................................................... 17

(6)Preparation of Paper .......................................................................... 18

(7) Directions for use ............................................................................... 19

(A) Standard folding of standard-size paper

............................................................................. 19

(B) Standard Folding of Non-standard-size Paper ......................................................................... 26

(C) How to Use the Interval Function ............................................................................................ 27

(8) Adjustment ......................................................................................... 29

(A) Fine Adjustment ....................................................................................................................... 29

(D) Paper Height Adjustment ......................................................................................................... 38

(E) Standard of Suction Air and Paper Feed Table Height ............................................................. 39

(F) Separator Height Adjustment .................................................................................................... 40

G) Changing Location of Paper Ejection Roller ............................................................................ 40

www.WhitakerBrothers.com

Summary of Contents for AeroFold 1500S





















































Search results

Summary of Contents for AeroFold 1500S

Reviews:

Related manuals for AeroFold 1500S

Brands by name

Popular brands

MBM AeroFold 1500S, Operation Manual

Search results

Summary of Contents for AeroFold 1500S

Reviews:

Related manuals for AeroFold 1500S

Brands by name

Popular brands