background image

GENUINE  CAR-NAVIGATION UNIT

 

INSTALLATION INSTRUCTIONS 

 

Thank you for purchasing a genuine Mazda accessory. 
Before removal and installation, be sure to thoroughly read these instructions. 
Please read the contents of this booklet in order to properly install and use the 
car-navigation unit. Your safety depends on it. 
Keep these instructions with your vehicle records for future reference.

 

 
 
 

  There are several 

WARNING

 and

 

CAUTION

 sections in this booklet concerning 

safety when installing or removing the car-navigation unit. Always read and follow them 
in order to prevent injuries, accidents, and possible damage to the vehicle. 

 

WARNING:

 

Indicates a situation in which serious injury or death could result if 

the warning is ignored. 

 

CAUTION:

 

Indicates a situation in which bodily injury or damage to the vehicle 

could result if the caution is ignored.

 

 For areas indicating the tightening torque in this instruction manual, tighten to the 

specified torque using a torque wrench. For areas in which the tightening torque is 
indicated inside parentheses ( ), the tightening torque is indicated as a reference value, 
however tightening using a torque wrench is not necessary. 

  Do not modify the car-navigation unit. 

  Do not install the car-navigation unit in any way other than described in the following 

instructions. 

 If in any doubt, please ask your Mazda dealer to install the accessory in order to 

prevent errors in installation. 

  If you have any questions about the use of the accessory, ask your Mazda dealer for 

proper advice before using it. 

 Mazda and its suppliers are not responsible for injuries, accidents, and damage to 

persons and property that arise from the failure of the dealer or installer to follow these 
instructions. 

 

To ensure safety and reliability of the work, installation, removal and disposal work 
must be carried out by an Authorized Mazda Dealership.

 

 

Be careful not to lose removed parts, and be sure that they are kept free from 
scratches, grease or other dirt.

 

 

 

PART NAME: CAR-NAVIGATION UNIT 

PART NUMBER: KF69 79 EZX      (MEXICO) 

KD37 79 EZX   (US/CANADA) 

VEHICLE: MAZDA CX-5 

 

 

To the dealer 

  Please turn over these instructions to the customer after installation.   

To the customer 

  Keep these instructions after installation. The instructions may be

 

necessary 

for installing other optional parts or removal of this accessory.

 

  Should the vehicle or this accessory be resold, always leave these instructions 

with it for the next owner. 

 

WARNING

NOTE 

00
00

 

GB 

00
00

 

00
00

 

Summary of Contents for KD37 79 EZX














Reviews: